Re: Betr.: Re: Redhat Enterprise 4 deadlock with cnxthsf_OsFloatSuffix error

"Linuxant support (Jonathan)" <[email protected]>
Newsgroups gmane.linux.drivers.modem.hsf
Message-ID <[email protected]>
Hi,

very little is known about this issue at the moment, the only known 
information is that it can only happen when you use the driver for 
multiple modems at the same time. A lot of users with that setup are not 
affected by this known issue for an unknown reason.

You could try with different versions of the Linux kernel. You could 
also try to move the modems to a different machine to see if there is a 
difference.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
[email protected]



Michel Prevenier wrote:
> 
> Hi there,
> 
> Thanks for the reply.
> 
> I removed the other 2 cards. Now the system doesn´t deadlock anymore.
> The cnxthsf_OsFloatSuffix messages are gone too.
> 
> But how can I get the other cards to work without crashing the system?
> 
> Regards,
> 
> Michel
> 
> 
> 
> *"Linuxant support (Jonathan)" <[email protected]>*
> 
> 20-09-2006 17:36
> 
> 	
> Aan
> 	Michel Prevenier <[email protected]>
> Cc
> 	[email protected]
> Onderwerp
> 	Re: [hsflinux] Redhat Enterprise 4 deadlock with cnxthsf_OsFloatSuffix 
> error
> 
> 
> 	
> 
> 
> 
> 
> 
> Hi,
> 
> a few other users have reported a similar problem when using more than
> one modem in the same machine. Can you try with only a single modem to
> see if you have the same problem or not?
> 
> Regards,
> 
> 
> Jonathan
> Technical specialist / Linuxant
> www.linuxant.com
> [email protected]
> 
> 
> 
> Michel Prevenier wrote:
>  >
>  > Hi,
>  >
>  > After installing the full version of the HSF driver the system
>  > completely hangs after a while.
>  >
>  > I tried the 2.6.9-24.0.2.EL.stk16smp kernel but that doesn´t solve the
>  > problem.
>  > The modems (I use 3 HSF modems in this system) are working correctly as
>  > long as the system stays up.
>  >
>  > In /var/log/messages I noticed these messages:
>  >
>  > cnxthsf_OsFloatSuffix: Id=9 used bit was FALSE !
>  >
>  > Id can have different values (1,4,7,2 etc.).
>  >
>  > I use the modems in a Hylafax configuration. Even when de modems aren´t
>  > active the system deadlocks after a while and the only option is to hard
>  > boot the machine.
>  > When I remove the HSF drivers the systems stays up.
>  >
>  > Any idea´s ?
>  >
>  > Thanx,
>  >
>  > Michel
>  >
>  >
>  >
>  >
>  >
>  >
>  >
>  >
>  > Let op!
>  > Met ingang van 12 april zijn onze e-mailadressen  gewijzigd! 
>  @achmea.nl wordt @achmeavastgoed.nl
>  > ********************* DISCLAIMER***************************
>  > De informatie in dit e-mail bericht is uitsluitend bestemd
>  > voor de geadresseerde. Verstrekking aan en
>  > gebruik door anderen is niet toegestaan. Door de
>  > electronische verzending van het bericht kunnen
>  > er geen rechten worden ontleend aan de
>  > informatie.
>  > *****************************************************************
>  >
>  >
>  > ------------------------------------------------------------------------
>  >
>  > _______________________________________________
>  > hsflinux mailing list
>  > [email protected]
>  > https://www.linuxant.com/mailman/listinfo/hsflinux
> 
> Let op! 
> Met ingang van 12 april zijn onze e-mailadressen  gewijzigd!  @achmea.nl wordt @achmeavastgoed.nl
> ********************* DISCLAIMER***************************
> De informatie in dit e-mail bericht is uitsluitend bestemd
> voor de geadresseerde. Verstrekking aan en
> gebruik door anderen is niet toegestaan. Door de
> electronische verzending van het bericht kunnen 
> er geen rechten worden ontleend aan de
> informatie.
> *****************************************************************
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> hsflinux mailing list
> [email protected]
> https://www.linuxant.com/mailman/listinfo/hsflinux
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.