Re: HSF modem picks up line but Does Not Dial

Hi,

everything seems fine in the dump you have provided, as far as the modem 
driver is concerned.

When you use 'AT &F X1' with "Init1", please make sure that you don't 
use "Init2" as these settings might override some settings if 'AT &F X1'.

Finally, you are using a 2.4 kernels and there is a lot of known IRQ 
issues with these kernels and an IRQ problem could be the source of the 
problem you have described. You could try with a 2.6 kernel to see if 
there is a difference.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
[email protected]



Daniele (Mastro) wrote:
>> hi.. im not the one here...
>> but i have the same problem:
>>
>> Country: Italy.. (i've setted it writing "ITALY" when asked in hsfconfig
>> --country)
>>
>> the modem is: Communication Controller: Rockwell International HSF 56k
>> Data/Fax Modem code (127a:2013)
>> PCI
>>
>> i've installed the latest version of the driver.. no problem during install
>>
>> than i tried with both ppp and wvdial, same problem: pick up the line (i
>> can ear
>>
>> here my wvdial.conf
>>
>> [Dialer Default]
>> Carrier Check = no  # Tried both with or without this
>> Init1 = ATZ         # i've tried AT &F X1, too
>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> Modem Type = Analog Modem
>> ISDN = 0
>> New PPPD = yes
>> Phone = .... # here my phone numbar
>> Modem = /dev/modem   # symlink to /dev/ttySHF0
>> Username = ...
>> Password = ...
>> Baud = 115200
>>
>> here the wvdial log without comment:
>>
>> ATZ
>> OK
>>
>> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> OK
>>
>> ATDTXXXXXXXXX     # the X are the numbar
>>
>> the line go down after a while..... and it retry with the same result
>>
>>
>> (can you or any other reply to me? i've not a subscription)
> 
> 
> sorry.. i forgotten the hsfdiag.txt...
> 
> here... hope you can help me..
> i noticed this in dmesg:
> 
> ttySHSF0 at I/O 0xde00 (irq = 9) is a Conexant HSF softmodem
> (PCI-127a:2013-1436:2113)
> usb.c: registered new driver hsfusbcd2
> usb.c: deregistering driver hsfusbcd2
> PCI: Found IRQ 9 for device 00:0a.0
> ttySHSF0 at I/O 0xde00 (irq = 9) is a Conexant HSF softmodem
> (PCI-127a:2013-1436:2113)
> usb.c: registered new driver hsfusbcd2
> usb.c: deregistering driver hsfusbcd2
> PCI: Found IRQ 9 for device 00:0a.0
> ttySHSF0 at I/O 0xde00 (irq = 9) is a Conexant HSF softmodem
> (PCI-127a:2013-1436:2113)
> usb.c: registered new driver hsfusbcd2
> usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 10 ret -32
> usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 4 ret -32
> 
> 
> thank you again,
> goodbye
> 
> _______________________________________________
> hsflinux mailing list
> [email protected]
> https://www.linuxant.com/mailman/listinfo/hsflinux