RE: Netgear WG511 802.11g problems...

Another follow up question...now that my netgear is up and working
(thanks), how would I go about setting wep?  I looked at the docs and it
says I need to use setoid...which I cannot compile (as shown below).

Thanks,
Matt

-----Original Message-----
From: Boex,Matthew W.
Sent: Tuesday, November 30, 2004 3:01 PM
To: '[email protected]'
Subject: Netgear WG511 802.11g problems...

Howdy,

Having problems getting my Netgear WG511 802.11g network card to work
with my FedoraCore2 ...stock install.  When I put the card in the pcmcia
slot I get...

------------------------
Nov 30 14:54:52 guac kernel: PCI: Enabling device 0000:07:00.0 (0000 ->
0002) Nov 30 14:54:53 guac kernel: prism54: request_firmware() failed
for 'isl3890'
Nov 30 14:54:53 guac kernel: eth1: could not upload firmware ('isl3890')
Nov 30 14:54:53 guac dhclient: sit0: unknown hardware address type 776
Nov 30 14:54:53 guac kernel: prism54: request_firmware() failed for
'isl3890'
Nov 30 14:54:53 guac kernel: eth1: could not upload firmware ('isl3890')
Nov 30 14:54:54 guac kernel: prism54: request_firmware() failed for
'isl3890'
Nov 30 14:54:54 guac kernel: eth1: could not upload firmware ('isl3890')
Nov 30 14:54:55 guac dhclient: sit0: unknown hardware address type 776
------------------------

So... I downloaded the firmware....

ISL3890-0.1.0.tar.gz

Untarred, and also loaded the kernel source from cd...

kernel-source-2.6.5-1.358.i386.rpm

Installed.  Now I go to the

cd ISL3890-0.1.0/pcmcia-cs-3.2.4-intersil  dir and run...

./Configure

Below is the output.   What am I doing wrong?

------------------------------------------------------------------------
-------
[root@guac pcmcia-cs-3.2.4-intersil]# ./Configure

    -------- Linux PCMCIA Configuration Script --------

The default responses for each question are correct for most users.
Consult the PCMCIA-HOWTO for additional info about each option.

PC card source directory
/home/boex/source/ISL3890-0.1.0/pcmcia-cs-3.2.4-intersil
Linux kernel source directory [/usr/src/linux]:

The kernel source tree is version 2.6.5-1.358custom.

!!!!!!!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!!!!!!!!
The current kernel is sublevel 2.6.5-1.358. Please check the target
kernel version and use the --extraver option to build for the correct
kernel image.
!!!!!!!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!!!!!!!!

The current kernel build date is Sat May 8 09:04:50 2004.

Build 'trusting' versions of card utilities (y/n) [y]: y Include 32-bit
(CardBus) card support (y/n) [y]: y Include PnP BIOS resource checking
(y/n) [n]:
Module install directory [/lib/modules/2.6.5-1.358]:
Include wireless ioctls (J. Tourrilhes) (y/n) [y]: y Include wireless
events (J. Tourrilhes) (y/n) [y]: y Include intersil events (y/n) [y]: y
Include Access Point WDS links (y/n) [n]:

ksyms: QM_MODULES: Function not implemented

ksyms: QM_MODULES: Function not implemented

(Repeated many time.....)

Kernel configuration options:
    Kernel-tree PCMCIA support is disabled.
    Symmetric multiprocessing support is disabled.
    Preemptive kernel support is disabled.
    High memory support is disabled.
    PCI BIOS support is disabled.
    Power management (APM) support is disabled.
    SCSI support is disabled.
    IEEE 1394 (FireWire) support is disabled.
    Networking support is disabled.
     Radio network interface support is enabled.
     Token Ring device support is disabled.
     Fast switching is disabled.
     Frame Diverter is disabled.
    Module version checking is disabled.
    Kernel debugging support is disabled.
    Preemptive kernel patch is disabled.
    /proc filesystem support is disabled.
    PAE support is disabled.

Cardbus support requires kernel PCI bus support!
    To fix, re-run 'make config' and disable Cardbus support.

Configuration failed.

E-MAIL CONFIDENTIALITY NOTICE:  The contents of this e-mail message and any attachments are intended solely for the
addressee(s) and may contain confidential and/or legally privileged information. If you are not the
intended recipient of this message or if this message has been addressed to you in error, please
immediately alert the sender by reply e-mail and then delete this message and any attachments. If you
are not the intended recipient, you are notified that any use, dissemination, distribution, copying, or
storage of this message or any attachment is strictly prohibited.