More info (Re: on-board rtl8139 fails.)

I just announced that I got it to work

In the working condition output from dmesg are interesting:

ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Unknown bridge resource 0: assuming transparent
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10, enabled at IRQ 9)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *5)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5, disabled)
ACPI: PCI Interrupt Link [LNKE] (IRQs *5)
ACPI: PCI Interrupt Link [LNKF] (IRQs *5)
ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
ACPI: PCI Interrupt Link [LNKH] (IRQs 5, disabled)
ACPI: Power Resource [FN10] (off)
ACPI: Power Resource [FN11] (off)
PCI: Probing PCI hardware
PCI: Using IRQ router SIS [1039/0008] at 00:02.0
PCI: Found IRQ 5 for device 00:02.7
SiS router pirq escape (99)
PCI: Found IRQ 9 for device 00:06.0
IRQ routing conflict for 00:08.0, have irq 10, want irq 9
IRQ routing conflict for 00:0c.0, have irq 10, want irq 9
PCI: Sharing IRQ 9 with 00:0d.0

If someone can explain what the problem *was* I would be really
happy. In particular what does the following mean?
--------------------------------------------
IRQ routing conflict for 00:08.0, have irq 10, want irq 9
IRQ routing conflict for 00:0c.0, have irq 10, want irq 9
--------------------------------------------
The working lspci -vv produces

00:00.0 Host bridge: Silicon Integrated Systems [SiS] 645DX Host
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=256M]
	Capabilities: [c0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
		Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=x4

00:01.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
	Memory behind bridge: e1000000-e1ffffff
	Prefetchable memory behind bridge: e2000000-efffffff
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 (rev 04)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80 [Master])
	Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 128
	Region 4: I/O ports at 1000 [size=16]

00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 PCI Audio Accelerator (rev a0)
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 2440
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 173 (13000ns min, 2750ns max)
	Interrupt: pin C routed to IRQ 5
	Region 0: I/O ports at 1400 [size=256]
	Region 1: I/O ports at 1080 [size=128]
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.0 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 0f) (prog-if 10 [OHCI])
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 7001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (20000ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.1 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 0f) (prog-if 10 [OHCI])
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 7001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (20000ns max)
	Interrupt: pin B routed to IRQ 5
	Region 0: Memory at e0001000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 0f) (prog-if 10 [OHCI])
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 7001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (20000ns max)
	Interrupt: pin C routed to IRQ 5
	Region 0: Memory at e0002000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.3 USB Controller: Silicon Integrated Systems [SiS]: Unknown device 7002 (prog-if 20 [EHCI])
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 7002
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (20000ns max)
	Interrupt: pin D routed to IRQ 5
	Region 0: Memory at e0003000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 Communication controller: Intel Corp.: Unknown device 1040
	Subsystem: Unknown device 16be:1040
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=4M]
	Capabilities: [e0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=375mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 2420
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 1800 [size=256]
	Region 1: Memory at e0004000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] Vital Product Data

00:0c.0 CardBus bridge: ENE Technology Inc: Unknown device 1410
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 1861
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
	16-bit legacy interface ports at 0001

00:0d.0 FireWire (IEEE 1394): Lucent Microelectronics FW323 (rev 04) (prog-if 10 [OHCI])
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 1881
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e0005000 (32-bit, non-prefetchable) [disabled] [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME+

01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 440 Go 64M] (rev a3) (prog-if 00 [VGA])
	Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 2441
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 248 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
	Region 2: Memory at e2000000 (32-bit, prefetchable) [size=512K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 2.0
		Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2,x4
		Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=x4


Notice that both the RTL8139 and the CardBus uses IRQ10 now.

Thanks for all the help

Please let me know if I can help improve the driver with the
reproducable bug I have on my system.

Jarl