Re: realtek 8139 problems
Cem Kizil <[email protected]> Wed, 9 Feb 2005 09:18:20 +1100 (EST)
| Newsgroups | gmane.linux.drivers.realtek.devel |
|---|---|
| Message-ID | <[email protected]> |
--===============1336438031== Content-Type: multipart/alternative; boundary="0-1141129649-1107901100=:347" Content-Transfer-Encoding: 8bit --0-1141129649-1107901100=:347 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: 8bit both cards are in the system at once, eth0 is 10Mbps rtl-8029 172.16.1.11 255.255.0.0, eth1 is rtl8139 172.16.1.12. My windows box is 172.16.1.10 255.255.0.0 My network setup is just P-2-P, just my windows box and my linux box. output of ifconfig is spot on, my 10Mb card at 172.161.1.11, no errors, and no packets dropped, zero collisions; exact same output for my rtl8139 except for ip address (172.16.1.12). route -n output: Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 172.16.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo no irq problems with two nic's, eth0 using 11 and eth1using 9. But on system startup it says my serial bus controller irq is 11, same as eth0's irq. but doubt very much thats problem because nic still functions with no problems. Nothing else uses irq 9. My 10Mb card works fine, both when the rtl8139 is connected in system and when removed. 8139 doesn't work when 10Mb card is connected in system; but works when 10Mb card is removed. not sure what flags, ref, use is, any definitions will be greatly appreciated. Cheers, Sam --------------------------------- Find local movie times and trailers on Yahoo! Movies. --0-1141129649-1107901100=:347 Content-Type: text/html; charset=iso-8859-1 Content-Transfer-Encoding: 8bit <DIV> <BLOCKQUOTE class=replbq style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid"> <P>both cards are in the system at once, eth0 is 10Mbps rtl-8029 172.16.1.11 255.255.0.0, eth1 is rtl8139 172.16.1.12.<BR>My windows box is 172.16.1.10 255.255.0.0 <BR>My network setup is just P-2-P, just my windows box and my linux box.<BR>output of ifconfig is spot on, my 10Mb card at 172.161.1.11, no errors, and no packets dropped, zero collisions; exact same output for my rtl8139 except for ip address (172.16.1.12).</P> <P>route -n output: </P> <P>Destination Gateway Genmask Flags Metric Ref Use Iface</P> <P>172.16.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0<BR>172.16.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1<BR>127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0  ; lo </P> <P><BR>no irq problems with two nic's, eth0 using 11 and eth1using 9. But on system startup it says my serial bus controller irq is 11, same as eth0's irq. but doubt very much thats problem because nic still functions with no problems. Nothing else uses irq 9.</P> <P>My 10Mb card works fine, both when the rtl8139 is connected in system and when removed. <BR>8139 doesn't work when 10Mb card is connected in system; but works when 10Mb card is removed.<BR>not sure what flags, ref, use is, any definitions will be greatly appreciated. </P> <P>Cheers,</P> <P>Sam</P> <P><BR><BR><BR><BR> </P></BLOCKQUOTE></DIV><p><br><hr size=1> Find local movie times and trailers on <a href="http://au.rd.yahoo.com/mail/tagline/*http://au.movies.yahoo.com" target=_blank><b>Yahoo! Movies.</b></a><br> --0-1141129649-1107901100=:347-- --===============1336438031== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline _______________________________________________ realtek mailing list [email protected] http://www.scyld.com/mailman/listinfo/realtek --===============1336438031==--