philips scp620nc [spca5xx_open:1985] DEALLOC error on spca50x_init_source

nicolas huchet <[email protected]>
Newsgroups gmane.linux.drivers.spca50x.devel
Message-ID <[email protected]>
Hello,

I have send the same mail yesterday but without subject. Perhaps the cause of no responds.
I try to run my new Philips SCP620NC webcam. But without success.
You'll can be interested by the result because, as you know, gspca doesn't support yet this model.
But I am interested too. :-)
I use debian with 2.6.18-5-486 kernel and gspcav1-20071224.tar.gz.
I give you all the information that i have:
 
nico@debian:~$ lsusb | grep Philips
Bus 002 Device 003: ID 0471:0333 Philips
 
I have written this in gspca_core.c (like SCP710NC and SCP600NC) :
 
case 0x0333:
spca50x->desc = PhilipsSPC620NC;
spca50x->bridge = BRIDGE_SN9CXXX;
spca50x->sensor = SENSOR_MI0360;
spca50x->customid = SN9C105;
spca50x->i2c_ctrl_reg = 0x81;
spca50x->i2c_base = 0x5d;
break;
 
But i have disassembled the webcam and star is written on the camera (z star ?).
Perhaps i don't use the good bridge and sensor. I have tried other bridges but,
as you can see, without success and a lots of error in dmesg when i load the module gspca.
 
After a modprbe gspca, dmesg returns me :
 
/home/nico/gspcav1-20071224/gspca_core.c: USB GSPCA camera found. SONIX JPEG (sn9c1xx)
/home/nico/gspcav1-20071224/gspca_core.c: [spca5xx_probe:4286] Camera type JPEG
/home/nico/gspcav1-20071224/gspca_core.c: [spca5xx_getcapability:1252] maxw 640 maxh 480 minw 160 minh 120
usbcore: registered new driver gspca
/home/nico/gspcav1-20071224/gspca_core.c: gspca driver 01.00.20 registered
 
I have also :
 
root@debian:/home/nico/gspcav1-20071224# ls -ail /dev/video0
8117 crw-rw---- 1 root video 81, 0 2008-01-29 15:32 /dev/video0
 
Everything is okay. But when i launch vlc /dev/video0, dmesg returns me:
 
/home/nico/gspcav1-20071224/gspca_core.c: [spca5xx_open:1985] DEALLOC error on spca50x_init_source
 
I have seen in a mailing list, that you ask to someone to load the module with debug option (debug=5) and send the full log.
But i don't know which shell request used.
 
I hope that you can help me, and i hope give you the results.

Regards,
 
Nicolas
 
PS : As you can see, english still experimental for me. I know, this is not an excuse but i am french... ;-)
_________________________________________________________________
Microsoft vous offre un logiciel pour classer, retoucher et partager vos photos !
http://www.windowslive.fr/galerie/
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.