Re: Osicom 123400-21 40port card
Jason Marshall <[email protected]>
| Newsgroups | gmane.linux.drivers.tulip.general |
|---|---|
| Message-ID | <[email protected]> |
> That's likely a Seeq (now owned by LSI Logic) transceiver made on the > 33rd week of 1996. What is the correct part number? 80222 is possible. Here's ALL the numbers: NQ80C269633, no question about it... There are four other chips that look similar, but have different numbers on them: FS9524AP/DP83223V/B FS9542AF/DP83223V/B FS9542APE4/DP83223V/B FS9542ATC4/DP83223V/B I don't know who made them, but their logo looks like a sideways N or Z with the ends of the letter curled in. Could these be national semiconductor TWISTER transceiver chips? Google thinks they might be! > > Should I give the new 0.95 version a go? > > Yes. Will do. > What is the full driver detection message? tulip.c:v0.93 11/7/2001 Written by Donald Becker <[email protected]> http://www.scyld.com/network/tulip.html eth0: Digital DS21140A Tulip rev 34 at 0xd4840000, 00:00:BC:11:31:A8, IRQ 10. eth0: EEPROM default media type Autosense. eth0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block. eth0: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block. eth0: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block. eth0: Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block. eth1: Digital DS21140A Tulip rev 34 at 0xd4842000, 00:00:BC:11:31:A9, IRQ 12. eth1: EEPROM default media type Autosense. eth1: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block. eth1: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block. eth1: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block. eth1: Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block. eth2: Digital DS21140A Tulip rev 34 at 0xd4844000, 00:00:BC:11:31:AA, IRQ 11. eth2: EEPROM default media type Autosense. eth2: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block. eth2: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block. eth2: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block. eth2: Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block. eth3: Digital DS21140A Tulip rev 34 at 0xd4846000, 00:00:BC:11:31:AB, IRQ 7. eth3: EEPROM default media type Autosense. eth3: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block. eth3: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block. eth3: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block. eth3: Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block. > Is the driver built-in or a module? Module -- I know I saw the docs for configuring that in the /etc/modules file or whatever, but you know, I just can't find it today. Hint? =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- | Jason Marshall, [email protected]. Spots InterConnect, Inc. Calgary, AB | =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- _______________________________________________ tulip mailing list, [email protected] To change to digest mode or unsubscribe visit http://www.scyld.com/mailman/listinfo/tulip