Re: Osicom 123400-21 40port card
Jason Marshall <[email protected]>
| Newsgroups | gmane.linux.drivers.tulip.general |
|---|---|
| Message-ID | <[email protected]> |
> OK, this is a normal SYM transceiver table, straight from reference design. That's a good sign. > > eth1: Digital DS21140A Tulip rev 34 at 0xd4842000, 00:00:BC:11:31:A9, IRQ 12. > > Curious: this board appears to have an EEPROM on all ports. Could you > please confirm with 'tulip-diag -e'? That would prevent the IRQ > correction code from triggering. Huh. It's amazing what you get for $10 on Ebay these days *8-) Only eth0 is plugged in right now. Okay, it's somewhat lengthy: omnivore2:/home/marshalj/tulip# ./tulip-diag -e tulip-diag.c:v2.11 6/17/2002 Donald Becker ([email protected]) http://www.scyld.com/diag/index.html Index #1: Found a Digital DS21140 Tulip adapter at 0xd800. Port selection is 10mpbs-serial, half-duplex. Transmit started, Receive started, half-duplex. The Rx process state is 'Waiting for packets'. The Tx process state is 'Idle'. The transmit threshold is 72. EEPROM 64 words, 6 address bits. PCI Subsystem IDs, vendor 0000, device 0000. CardBus Information Structure at offset 00000000. Ethernet MAC Station Address 00:00:BC:11:31:A8. EEPROM transceiver/media description table. Leaf node at offset 30, default media type 0800 (Autosense). CSR12 direction setting bits 0x0f. 4 transceiver description blocks: 21140 Non-MII transceiver for media 0 (10baseT). CSR12 control port setting 0x01, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 3 (100baseTx). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. 21140 Non-MII transceiver for media 4 (10baseT-Full Duplex). CSR12 control port setting 0x09, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 5 (100baseTx Full Duplex). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. Index #2: Found a Digital DS21140 Tulip adapter at 0xd400. Port selection is 10mpbs-serial, half-duplex. Transmit stopped, Receive stopped, half-duplex. The Rx process state is 'Stopped'. The Tx process state is 'Stopped'. The transmit threshold is 72. EEPROM 64 words, 6 address bits. PCI Subsystem IDs, vendor 0000, device 0000. CardBus Information Structure at offset 00000000. Ethernet MAC Station Address 00:00:BC:11:31:A9. EEPROM transceiver/media description table. Leaf node at offset 30, default media type 0800 (Autosense). CSR12 direction setting bits 0x0f. 4 transceiver description blocks: 21140 Non-MII transceiver for media 0 (10baseT). CSR12 control port setting 0x01, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 3 (100baseTx). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. 21140 Non-MII transceiver for media 4 (10baseT-Full Duplex). CSR12 control port setting 0x09, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 5 (100baseTx Full Duplex). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. Index #3: Found a Digital DS21140 Tulip adapter at 0xd000. Port selection is 10mpbs-serial, half-duplex. Transmit stopped, Receive stopped, half-duplex. The Rx process state is 'Stopped'. The Tx process state is 'Stopped'. The transmit threshold is 72. EEPROM 64 words, 6 address bits. PCI Subsystem IDs, vendor 0000, device 0000. CardBus Information Structure at offset 00000000. Ethernet MAC Station Address 00:00:BC:11:31:AA. EEPROM transceiver/media description table. Leaf node at offset 30, default media type 0800 (Autosense). CSR12 direction setting bits 0x0f. 4 transceiver description blocks: 21140 Non-MII transceiver for media 0 (10baseT). CSR12 control port setting 0x01, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 3 (100baseTx). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. 21140 Non-MII transceiver for media 4 (10baseT-Full Duplex). CSR12 control port setting 0x09, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 5 (100baseTx Full Duplex). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. Index #4: Found a Digital DS21140 Tulip adapter at 0xb800. Port selection is 10mpbs-serial, half-duplex. Transmit stopped, Receive stopped, half-duplex. The Rx process state is 'Stopped'. The Tx process state is 'Stopped'. The transmit threshold is 72. EEPROM 64 words, 6 address bits. PCI Subsystem IDs, vendor 0000, device 0000. CardBus Information Structure at offset 00000000. Ethernet MAC Station Address 00:00:BC:11:31:AB. EEPROM transceiver/media description table. Leaf node at offset 30, default media type 0800 (Autosense). CSR12 direction setting bits 0x0f. 4 transceiver description blocks: 21140 Non-MII transceiver for media 0 (10baseT). CSR12 control port setting 0x01, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 3 (100baseTx). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. 21140 Non-MII transceiver for media 4 (10baseT-Full Duplex). CSR12 control port setting 0x09, command 00 0x8e. Media detection by looking for a 0 on bit 7 of the CSR12 control port. 21140 Non-MII transceiver for media 5 (100baseTx Full Duplex). CSR12 control port setting 0x01, command 00 0x6d. Media detection by looking for a 1 on bit 6 of the CSR12 control port. There it is, verbatim. > > Module -- I know I saw the docs for configuring that in the /etc/modules > > file or whatever, but you know, I just can't find it today. Hint? > > What does /etc/modules.conf report? > What does running 'lsmod' report? I mis-spoke -- I know for certain that it's a module, and that it's insmod'd. It was the "probe-backwards" switch I didn't know how to set. Personally, if the backwards listing of MAC address isn't hurting anything, I'd just as soon not change anything. If you disagree, then by all means I can tweak things on that end. =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- | Jason Marshall, [email protected]. Spots InterConnect, Inc. Calgary, AB | =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- _______________________________________________ tulip mailing list, [email protected] To change to digest mode or unsubscribe visit http://www.scyld.com/mailman/listinfo/tulip