(tulip) Device or resource busy error too

Hi for all the list !
I'm a trying to install the driver tulip in Slackware 3.0 with kernel
2.2.13, but I'm not to succeed.
Did have same person to succeed?

Bye ....

----- Original Message -----
From: <[email protected]>
To: <[email protected]>
Sent: Thursday, August 08, 2002 1:02 PM
Subject: tulip digest, Vol 1 #589 - 2 msgs


> Send tulip mailing list submissions to
> [email protected]
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://www.scyld.com/mailman/listinfo/tulip
> or, via email, send a message with subject or body 'help' to
> [email protected]
>
> You can reach the person managing the list at
> [email protected]
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of tulip digest..."
>
>
> Today's Topics:
>
>    1. Device or resource busy error (vinod asokan)
>    2. Re: Device or resource busy error (vinod asokan)
>
> --__--__--
>
> Message: 1
> From: "vinod asokan" <[email protected]>
> To: "tulip" <[email protected]>
> Date: Thu, 8 Aug 2002 15:36:23 +0900
> Subject: [tulip] Device or resource busy error
>
> Hi,
>
> Our company makes Network cards. The current development card is a Fibre
> mode card.
> It uses 21143-TD MAC chip and intel LXT971A PHY chip.
>
> The designated card has Fx mode enabled by means of hardware setting.
> I am using Turbo Linux 7.0 in a Toshiba dynabook PC.
> The pcmcia-cs-3.1.27 service loads the tulip_cb driver. The card runs
fine.
> Ping  as well ftp works fine. The file transfer (peer to peer) also works
> with
> considerable speed.
>
> But everytime I remove the card or , when I use "service pcmcia restart",
> The kernel message says the " device or resource busy".
>
> "lsmod tulip_cb "  also does not work. I have to ultimately reboot the
> system , to free the
> pcmacia resources.
> Is there any other way by which I can stop the pcmcia service or unload
the
> driver..?
>
> Can anyone  tell me the possible reasons for the "resource busy " error
> message ??
>
> Thanks and regards
> ***********************************************
> Vinod Asokan
>
>
>
> --__--__--
>
> Message: 2
> From: "vinod asokan" <[email protected]>
> To: "tulip" <[email protected]>, "Florian" <[email protected]>
> Subject: Re: [tulip] Device or resource busy error
> Date: Thu, 8 Aug 2002 21:02:15 +0900
>
> hi,
> I had tried
> "ifconfig eth1 down "
> also "rmmod tulip_cb"
>
> Similar message  "device or resource busy " is displayed when I try these.
>
> Could this problem occur , if there is a problem in the hardware?
> Since the pcmcia-cs service is loading the driver, is it possible for me
> kill a process ?
>
> It is very tedious to reboot every time We remove the card from PCMCIA
slot.
>
> Any help would be appreciable..
> thanks in advance!!
>
> ***********************************************
> Vinod Asokan
> Hirakawa Hewtech Corp.(Koga)
> Ibaraki, Japan.
> Mobile: +81- 70- 6104 4418
> [email protected]
>
>
> ----- Original Message -----
> From: Florian
> To: vinod asokan
> Sent: Thursday, August 08, 2002 8:37 PM
> Subject: Re: [tulip] Device or resource busy error
>
>
> what i would try:
>
> do an "ifdown eth0" (or whatever) first
> maybe followed by a "rmmod tulip_cb"
>
> On 8 Aug 2002 at 15:36, vinod asokan wrote:
>
> > Hi,
> >
> > Our company makes Network cards. The current development card is a Fibre
> > mode card.
> > It uses 21143-TD MAC chip and intel LXT971A PHY chip.
> >
> > The designated card has Fx mode enabled by means of hardware setting.
> > I am using Turbo Linux 7.0 in a Toshiba dynabook PC.
> > The pcmcia-cs-3.1.27 service loads the tulip_cb driver. The card runs
> fine.
> > Ping  as well ftp works fine. The file transfer (peer to peer) also
works
> > with
> > considerable speed.
> >
> > But everytime I remove the card or , when I use "service pcmcia
restart",
> > The kernel message says the " device or resource busy".
> >
> > "lsmod tulip_cb "  also does not work. I have to ultimately reboot the
> > system , to free the
> > pcmacia resources.
> > Is there any other way by which I can stop the pcmcia service or unload
> the
> > driver..?
> >
> > Can anyone  tell me the possible reasons for the "resource busy " error
> > message ??
> >
> > Thanks and regards
> > ***********************************************
> > Vinod Asokan
> >
> >
> > _______________________________________________
> > tulip mailing list, [email protected]
> > To change to digest mode or unsubscribe visit
> > http://www.scyld.com/mailman/listinfo/tulip
>
>
>
> --__--__--
>
> _______________________________________________
> tulip mailing list
> [email protected]
> http://www.scyld.com/mailman/listinfo/tulip
>
>
> End of tulip Digest

_______________________________________________
tulip mailing list, [email protected]
To change to digest mode or unsubscribe visit
http://www.scyld.com/mailman/listinfo/tulip