Not assigned an IRQ for an FA511

RH7.3 ships eith PCMCIA based on pcmcia-cs-3.1.22.  This code is getting long 
in the tooth, so I rebuilt kernel without PCMCIA support and installed 
pcmcia-cs-3.2.3.  The PCMCIA subsystem started OK and tulip_cb loaded OK.  
But, as expected, the card would only slowly transmit and not receive.

So, I installed the scyld netdrivers.  Made entries in /etc/pcmcia/config for 
the tulip driver.  Once again, the PCMCIA subsystem starts OK ...
Module                  Size  Used by    Not tainted
cs4232                  4960   2  (autoclean)
ad1848                 23552   0  (autoclean) [cs4232]
uart401                 7776   0  (autoclean) [cs4232]
sound                  69164   2  [cs4232 ad1848 uart401]
abi-sco                13848   0  (unused)
abi-cxenix              7680   0  [abi-sco]
abi-svr4               77872   0  [abi-sco abi-cxenix]
lcall7                  2228   0  [abi-sco abi-cxenix]
abi-util                1404   0  [lcall7]
binfmt_coff             6676   0
mwave                  31812   4
apm                    12324   2
ds                      8352   2
i82365                 26416   2
pcmcia_core            43872   0  [ds i82365]
mousedev                5024   1
hid                    20608   0  (unused)
input                   5728   0  [mousedev hid]
rtc                     7612   0  (autoclean)

However, tulip does not load.  Here is dmesg ...
PCI: Found IRQ 11 for device 00:07.2
uhci.c: USB UHCI at I/O 0x8400, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 76k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: USB new device connect on bus1/1/4, assigned device number 3
usb.c: USB device 3 (vend/prod 0x45e/0x40) is not claimed by any active 
driver.
Real Time Clock Driver v1.10e
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input0: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse Optical®] on 
usb1:3
.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
Adding Swap: 204080k swap-space (priority -1)
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,5), internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
pci-scan.c:v1.11 8/31/2002  Donald Becker <[email protected]> 
http://www.scyld.co
m/linux/drivers.html
tulip.c:v0.95f 11/17/2002  Written by Donald Becker <[email protected]>
  http://www.scyld.com/network/tulip.html
Linux PCMCIA Card Services 3.2.3
  kernel build: 2.4.18-19.7.x-Jan15 #2 Wed Jan 15 22:05:07 EST 2003
  options:  [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:06.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Found IRQ 11 for device 00:02.1
  TI 1251A rev 00 PCI-to-CardBus at slot 00:02, mem 0x50102000
    host opts [0]: [ring] [isa irq] [pci irq 11] [lat 168/176] [bus 2/4]
    host opts [1]: [ring] [isa irq] [pci irq 11] [lat 168/176] [bus 5/7]
    ISA irqs (scanned) = 3,4,7,10 PCI status changes
cs: cb_alloc(bus 2): vendor 0x1317, device 0x1985
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
ttyS1 at port 0x02f8 (irq = 3) is a 16550A
pci-scan.c:v1.11 8/31/2002  Donald Becker <[email protected]> 
http://www.scyld.co
m/linux/drivers.html
tulip.c:v0.95f 11/17/2002  Written by Donald Becker <[email protected]>
  http://www.scyld.com/network/tulip.html
PCI device 'ADMtek Centaur-C' was not assigned an IRQ.
It will not be activated.
pci-scan.c:v1.11 8/31/2002  Donald Becker <[email protected]> 
http://www.scyld.co
m/linux/drivers.html
tulip.c:v0.95f 11/17/2002  Written by Donald Becker <[email protected]>
  http://www.scyld.com/network/tulip.html
PCI device 'ADMtek Centaur-C' was not assigned an IRQ.
It will not be activated.

And lspci -v -n gives ...
pcilib: Cannot open /proc/bus/pci/02/00.0
lspci: Unable to read 64 bytes of configuration space.

Any help appreciated.
-- 
                                  Robert March
                              St Andrew's House
                          L'Orignal  ON  K0B 1K0
_______________________________________________
tulip mailing list, [email protected]
To change to digest mode or unsubscribe visit
http://www.scyld.com/mailman/listinfo/tulip