Netgear FA511 on RedHat 7.3

Greets -

First off, thanks for everyone's effort to provide this device driver.  

I'm having trouble with a Netgear FA511 on RedHat 7.3.  I'm currently
running kernel 2.4.18-17.7.x.  I have downloaded and compiled the most
recent netdrivers.tgz, and placed the resulting modules in
/lib/modules/2.4.18-17.7.x/kernel/drivers/net.  When I insmod tulip, it
confirms that it is loading the module from that location.

The primary symptom is that when I attempt (or the system attempts to)
bring up the interface, the machine locks up hard (it's a Micron
Transport XT2, if that matters).  The card is CardBus.

Here's some stuff that seems relevant from dmesg:

May 16 08:54:14 linuxlt pcmcia:  cardmgr.
May 16 08:54:14 linuxlt cardmgr[809]: starting, version is 3.1.22
May 16 08:54:14 linuxlt rc: Starting pcmcia:  succeeded
May 16 08:54:14 linuxlt /etc/hotplug/pci.agent: Setup tulip for PCI slot
03:00.0

May 16 08:54:14 linuxlt cardmgr[809]: watching 2 sockets
May 16 08:54:14 linuxlt kernel: cs: IO port probe 0x0c00-0x0cff: clean.
May 16 08:54:14 linuxlt kernel: cs: IO port probe 0x0100-0x04ff:
excluding 0x378-0x37f 0x4d0-0x4d7
May 16 08:54:14 linuxlt kernel: cs: IO port probe 0x0a00-0x0aff: clean.
May 16 08:54:14 linuxlt kernel: tulip.c:v0.95f 11/17/2002  Written by
Donald Becker <[email protected]>
May 16 08:54:14 linuxlt kernel:  
http://www.scyld.com/network/tulip.html
May 16 08:54:14 linuxlt kernel:   The PCI BIOS has not enabled the
device at 3/0!  Updating PCI command 0003->0007.
May 16 08:54:14 linuxlt cardmgr[809]: initializing socket 0
May 16 08:54:14 linuxlt cardmgr[809]: socket 0: Netgear FA511
May 16 08:54:14 linuxlt kernel: eth1: ADMtek Centaur-C rev 17 at
0xd00b2000, 00:10:7A:69:94:71, IRQ 10.
M

I've added the following lines to my /etc/pcmcia/config to get Card
Services to recognize the card:

card "Netgear FA511"
  version "N"
  bind "tulip"

Note that that is ALL the information the card returns when it's an
unrecognized device - no manfid or additional version info appears in
dmesg (there are two PCIIds, but I couldn't get the card to be
identified by specifying them instead of the version).

lsmod shows this:

Module                  Size  Used by    Not tainted
tulip                  36064   0  (unused)
agpgart                38720   4  (autoclean)
nfsd                   73664   8  (autoclean)
lockd                  54144   1  (autoclean) [nfsd]
sunrpc                 72052   1  (autoclean) [nfsd lockd]
ds                      8160   2
yenta_socket           11488   2
pcmcia_core            47648   0  [ds yenta_socket]
eepro100               18592   1
pci-scan                4924   2  [tulip eepro100]
usb-uhci               23332   0  (unused)
usbcore                69088   1  [usb-uhci]
ext3                   62144   4
jbd                    46004   4  [ext3]

Note that there IS another (built-in) ethernet card present.  It's using
the eepro100 module, and functions perfectly.

I know this can't be all the debugging information you would want, so
please let me know what additional info you'd like.

Thanks in advance for any help you can give!

Regards,
jared

-- 
Jared Warren
Adventa Control Technologies
972.543.1690

_______________________________________________
tulip mailing list, [email protected]
To change to digest mode or unsubscribe visit
http://www.scyld.com/mailman/listinfo/tulip