Re: Can't transmit with new kernel

I am having exactly the same trouble.  It seems that the card can=20
receive but not transmit.  I also have tried multiple kernels; it seems=20
that the last time that it worked was 2.4.17, and before that 2.2.20. =20
I have tried 2.4.20, 2.4.22, 2.6.0, 2.6.1, and 2.6.1-benh.I also can't=20
compile the diagnostics, and my ifconfig looks very similar.  I have=20
tried so many things, and am at the end of my skills.  If anyone has=20
any help, I would appreciate it greatly (and I'm sure that Bill will to=20
:) )
Thanks,
Steven



> Hello everybody, got a problem and would love to get some help :).
>
>
> For over a month I have been trying to get my Linksys 10/100 NIC to=20
> work
> with Debian 3.0. When I initially install Debian, with the 2.2.20=20
> kernel,
> the card works fine. If I try to update the kernel though, the card=20
> stops
> working. I have tried numerous newer kernels (2.4.19 - 2.4.23, and=20
> 2.6.) I
> have also tried compiling tulip support into the kernel as well as=20
> using the
> driver as a module. Finally, I have also tried installing the tulip=20
> drivers
> avialable on the website (v0.97.) In all cases the card stops working.=20
> In
> particular, it seems that the card can recieve, but not send, packets.=20
> For
> instances, here is a typical ifconfig output
>
>
> "eth0 Link encap:Ethernet HWaddr 00:4C:69:6E:75:79
> =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0UP BROADCAST RUNNING MULTICAS=
T MTU:1500 Metric:1
> =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0RX packets:23 errors:0 droppe=
d:0 overruns:0 frame:0
> =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0TX packets:0 errors:0 dropped=
:0 overruns:0 carrier:0
> =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0collisions:0 txqueuelen:1000
> =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0RX bytes:1380 (1.3 KiB) TX by=
tes:0 (0.0 b)
> =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0Interrupt:5 Base address:0xa0=
00 "
>
>
> Also, I tried using Tulip-Diag but was not able to compile the program=20
> even
> though I followed the directions at the end of the file. When I try to
> compile tulip-diag I get hundreds of errors, which can be found at
> http://s92790223.onlinehome.us/Personal/diagCompile.txt
>
>
> Are there any suggestions out there for a poor, inexperienced linux=20
> guy?


------------------

Steven Schlansker
_______________________________________________
tulip mailing list, [email protected]
To change to digest mode or unsubscribe visit
http://www.scyld.com/mailman/listinfo/tulip