Re: Zoom Internal Cable Modem
Alistair Moir <[email protected]> Mon, 2 Feb 2004 22:48:03 -0800 (PST)
| Newsgroups | gmane.linux.drivers.tulip.general |
|---|---|
| Message-ID | <[email protected]> |
Further to my original email here are four tulip-diaf -fa outputs the first shows the card after inital set up, all is running well, the other three are when the card is down. As before _ANY_ feedback would be appreciated. The messages in the log are :- NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, status f4260000, CSR12 ffffffff, resetting... tulip-diag.c:v2.17 5/6/2003 Donald Becker ([email protected]) http://www.scyld.com/diag/index.html Index #1: Found a Conexant LANfinity adapter at 0xe800. Conexant LANfinity chip registers at 0xe800: 0x00: fff88000 ffffffff ffffffff 1b503000 1b503200 f4660000 e0042002 7bffebef 0x40: fffe0000 fff080e8 fffe0000 fffe0000 ffffffff ffffffff ffffffff f7f8fec8 Extended registers: 0x80: cc660000 cbffebef f0000019 ffff00ff ffffffff 1b503260 1b5030c0 00000000 0xa0: ffffffff 00000001 00000001 00000001 00000000 00000000 00000000 00000000 0xc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 0xe0: 00000000 00000000 00000000 00000000 ffffffff 00000000 00000000 00000000 Port selection is MII, half-duplex. Transmit started, Receive started. The Rx process state is 'Waiting for packets'. The Tx process state is 'Idle'. The transmit threshold is 128. tulip-diag.c:v2.17 5/6/2003 Donald Becker ([email protected]) http://www.scyld.com/diag/index.html Index #1: Found a Conexant LANfinity adapter at 0xe800. Conexant LANfinity chip registers at 0xe800: 0x00: fff88000 ffffffff ffffffff 26aa7000 26aa7200 f4660000 e0042002 7bffebef 0x40: fffe0000 fffc80e8 fffe0000 fffe0000 ffffffff ffffffff ffffffff f7f9fec8 Extended registers: 0x80: cc660000 cbffebef f0000019 ffff00ff ffffffff 26aa7260 26aa7090 00000000 0xa0: ffffffff 00000000 00000000 00000000 00000000 00000000 00000000 00000000 0xc0: 00000000 00000000 00000000 00000000 00000000 0000040b 00000000 00000000 0xe0: 00000000 00000000 00000000 000000ff ffffffff 00000000 00000000 00000000 Port selection is MII, half-duplex. Transmit started, Receive started. The Rx process state is 'Waiting for packets'. The Tx process state is 'Idle'. The transmit threshold is 128. tulip-diag.c:v2.17 5/6/2003 Donald Becker ([email protected]) http://www.scyld.com/diag/index.html Index #1: Found a Conexant LANfinity adapter at 0xe800. Conexant LANfinity chip registers at 0xe800: 0x00: fff88000 ffffffff ffffffff 26aa7000 26aa7200 f4260000 e0042002 7bffebef 0x40: fffe0000 fff080e8 fffe0000 fffe0000 ffffffff ffffffff ffffffff f7f8fec8 Extended registers: 0x80: cc260000 cbffebef f0000019 ffff00ff ffffffff 26aa72c0 26aa71c0 00000000 0xa0: ffffffff 00000002 00000002 00000002 00000000 00000000 00000000 00000000 0xc0: 00000000 00000000 00000000 00000000 00000000 0000ffff 00000000 00000000 0xe0: 00000000 00000000 00000000 000000ff ffffffff 00000000 00000000 00000000 Port selection is MII, half-duplex. Transmit started, Receive started. The Rx process state is 'Waiting for packets'. The Tx process state is 'Waiting for Tx to finish'. The transmit threshold is 128. tulip-diag.c:v2.17 5/6/2003 Donald Becker ([email protected]) http://www.scyld.com/diag/index.html Index #1: Found a Conexant LANfinity adapter at 0xe800. Conexant LANfinity chip registers at 0xe800: 0x00: fff88000 ffffffff ffffffff 20d32000 20d32200 f4260000 e0042002 7bffebef 0x40: fffe0000 fffc80e8 fffe0000 fffe0000 ffffffff ffffffff ffffffff f7f8fec8 Extended registers: 0x80: cc260000 cbffebef f0000019 ffff00ff ffffffff 20d322f0 20d321f0 00000000 0xa0: ffffffff 00000002 00000002 00000002 00000000 00000000 00000000 00000000 0xc0: 00000000 00000000 00000000 00000000 00000000 0000ffff 00000000 00000000 0xe0: 00000000 00000000 00000000 000000ff ffffffff 00000000 00000000 00000000 Port selection is MII, half-duplex. Transmit started, Receive started. The Rx process state is 'Waiting for packets'. The Tx process state is 'Waiting for Tx to finish'. The transmit threshold is 128. --- Alistair Moir <[email protected]> wrote: > Hi, > I have a Zoom 5001 Internal PCI Cable Modem. This card has been > discussed on this list before. > http://www.scyld.com/pipermail/tulip/2002-January/003963.html > http://www.scyld.com/pipermail/tulip/2002-April/004128.html > > > Needless to state, I'm having problems :-( The card is recognised, > the tulip module gets everything set up and once DHCP has done it's > stuff we're off and running. However, ifconfig shows everything is > not > peachy and before long the card hangs. > > > Sometimes, taking the interface down, removing the module, installing > the module and bring up the interface works. Mostly it's a reboot to > get everything going again. > > > I have a Dell Dimension with an onboard 3c905. The onboard card does > not seem to be the problem. I've tried disabling it in the bios, not > loading the kernal module and not bringing up the interface. No go, > the Zoom still hangs. > > > I run debian with 2.4.22 and I've tried the latest drivers from > www.sycd.com. No go, the card hangs with either driver. The new > drivers seem better but I've no imperical evidence of this. > > > I will attempt to modify the driver as suggested back in 2002, but > shouldn't those changes be in the latest download? I'm open to > suggestions and more than willing to help test ideas to get this card > up and running. So, what should I do next? > > Below is the output from various commands that I think might help. I > would use the diagnostics but I seem to be getting compile errors, if > I sort that out I'll provide more info and maybe a patch to the diags > if needed. > > > Here is the results of lspci > > 00:00.0 Host bridge: Intel Corp. 82850 850 (Tehama) Chipset Host > Bridge (MCH) (rev 02) > 00:01.0 PCI bridge: Intel Corp. 82850 850 (Tehama) Chipset AGP Bridge > (rev 02) > 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 02) > 00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 02) > 00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 02) > 00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 02) > 00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 02) > 00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 02) > 01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 > MX/MX 400] (rev a1) > 02:07.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 > (rev 07) > 02:07.1 Input device controller: Creative Labs SB Live! MIDI/Game > Port (rev 07) > 02:08.0 Multimedia video controller: Brooktree Corporation Bt878 > Video > Capture (rev 11) > 02:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio > Capture (rev 11) > 02:09.0 Ethernet controller: Conexant HCF 56k Modem (rev 08) > 02:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M > [Tornado] (rev 78) > > > Here's the results of insmod with the old driver > > Nov 27 20:44:35 galaga kernel: Linux Tulip driver version > 0.9.15-pre12 (Aug 9, 2002) > Nov 27 20:44:35 galaga kernel: PCI: Found IRQ 7 for device 02:09.0 > Nov 27 20:44:35 galaga kernel: PCI: Sharing IRQ 7 with 02:0c.0 > Nov 27 20:44:35 galaga kernel: eth1: Conexant LANfinity rev 8 at > 0xe800, EEPROM not present, 00:4C:69:6E:75:79, IRQ 7. > > > Here's the results of insmod with the new driver > > Nov 27 20:38:56 galaga kernel: tulip.c:v0.97 7/22/2003 Written by > Donald Becker <[email protected]> > Nov 27 20:38:56 galaga kernel: > http://www.scyld.com/network/tulip.html > Nov 27 20:38:56 galaga kernel: eth1: Conexant LANfinity rev 8 at > 0xe892c000, 00:40:36:09:52:32, IRQ 7. > > > Sample ifconfig just after start up > > eth1 Link encap:Ethernet HWaddr 00:4C:69:6E:75:79 > inet addr:24.7.72.27 Bcast:255.255.255.255 > Mask:255.255.248.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:929 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:3 dropped:0 overruns:0 carrier:6 > collisions:0 txqueuelen:100 > RX bytes:56656 (55.3 KiB) TX bytes:0 (0.0 b) > Interrupt:7 Base address:0xe800 > > > Sample ifconfig just after failure > > eth1 Link encap:Ethernet HWaddr 00:4C:69:6E:75:79 > inet addr:24.7.72.27 Bcast:255.255.255.255 > Mask:255.255.248.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:7096 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:64 dropped:0 overruns:0 carrier:152 > collisions:0 txqueuelen:100 > RX bytes:485976 (474.5 KiB) TX bytes:0 (0.0 b) > Interrupt:7 Base address:0xe800 > > > /proc/pci > > PCI devices found: > Bus 0, device 0, function 0: > Host bridge: Intel Corp. 82850 850 (Tehama) Chipset Host Bridge > (MCH) (rev 2). > Prefetchable 32 bit memory at 0xf0000000 [0xf3ffffff]. > Bus 0, device 1, function 0: > PCI bridge: Intel Corp. 82850 850 (Tehama) Chipset AGP Bridge > (rev > 2). > Master Capable. Latency=64. Min Gnt=14. > Bus 0, device 30, function 0: > PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 2). > Master Capable. No bursts. Min Gnt=6. > Bus 0, device 31, function 0: > ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 2). > Bus 0, device 31, function 1: > IDE interface: Intel Corp. 82801BA IDE U100 (rev 2). > I/O at 0xffa0 [0xffaf]. > Bus 0, device 31, function 2: > USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 2). > IRQ 12. > I/O at 0xff80 [0xff9f]. > Bus 0, device 31, function 3: > SMBus: Intel Corp. 82801BA/BAM SMBus (rev 2). > IRQ 11. > I/O at 0xdcd0 [0xdcdf]. > Bus 0, device 31, function 4: > USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 2). > IRQ 10. > I/O at 0xff60 [0xff7f]. > Bus 1, device 0, function 0: > VGA compatible controller: nVidia Corporation NV11 [GeForce2 > MX/MX > 400] (rev 161). > IRQ 9. > Master Capable. Latency=64. Min Gnt=5.Max Lat=1. > Non-prefetchable 32 bit memory at 0xfd000000 [0xfdffffff]. > Prefetchable 32 bit memory at 0xe8000000 [0xefffffff]. > Bus 2, device 7, function 0: > Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev > 7). > IRQ 9. > Master Capable. Latency=64. Min Gnt=2.Max Lat=20. > I/O at 0xece0 [0xecff]. > Bus 2, device 7, function 1: > Input device controller: Creative Labs SB Live! MIDI/Game Port > (rev > 7). > Master Capable. Latency=64. > I/O at 0xecd8 [0xecdf]. > Bus 2, device 8, function 0: > Multimedia video controller: Brooktree Corporation Bt878 Video > Capture (rev 17). > IRQ 11. > Master Capable. Latency=64. Min Gnt=16.Max Lat=40. > Prefetchable 32 bit memory at 0xf4001000 [0xf4001fff]. > Bus 2, device 8, function 1: > Multimedia controller: Brooktree Corporation Bt878 Audio Capture > (rev 17). > IRQ 11. > Master Capable. Latency=64. Min Gnt=4.Max Lat=255. > Prefetchable 32 bit memory at 0xf4000000 [0xf4000fff]. > Bus 2, device 9, function 0: > Ethernet controller: Conexant HCF 56k Modem (rev 8). > IRQ 7. > Master Capable. Latency=64. Min Gnt=20.Max Lat=40. > I/O at 0xe800 [0xe8ff]. > Non-prefetchable 32 bit memory at 0xfbffc000 [0xfbffffff]. > Bus 2, device 12, function 0: > Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] > (rev > 120). > IRQ 7. > Master Capable. Latency=64. Min Gnt=10.Max Lat=10. > I/O at 0xec00 [0xec7f]. > Non-prefetchable 32 bit memory at 0xfbff7c00 [0xfbff7c7f]. > > > ===== > +-----------------------------------------------+ > | /\ |\/| | > | /--\LISTAIR | |OIR. [email protected] | > +-----------------------------------------------+ > ===== +-----------------------------------------------+ | /\ |\/| | | /--\LISTAIR | |OIR. [email protected] | +-----------------------------------------------+ _______________________________________________ tulip mailing list, [email protected] To change to digest mode or unsubscribe visit http://www.scyld.com/mailman/listinfo/tulip