3c905 not loading with new kernel

I have recently upgraded from kernel 4.2.20 to 4.4.23 on debain.  I have two
3c905 cards and neither will load up with the new kernel.  I compiled in the
driver support for the 3c90x series so there should be no problems.  Below
is the output from dmesg and also lspci -vv.  Let me know if you need
anything else to help me diagnose my problem.

Thanks.

Clay

>>>>>>>>>>
dmseg

Linux version 2.4.23 (root@nelson) (gcc version 2.95.4 20011002 (Debian
prerelease)) #4 Wed Dec 1
7 19:14:39 PST 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
128MB LOWMEM available.
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=Linux ro root=305
Initializing CPU#0
Detected 400.915 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.53 BogoMIPS
Memory: 126980k/131072k available (1342k kernel code, 3704k reserved, 447k
data, 284k init, 0k hi
ghmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU:             Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 00:07.0
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 [email protected]).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PCI: Found IRQ 10 for device 00:13.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:13.0: 3Com PCI 3c905 Boomerang 100baseTx at 0xe800. Vers LK1.1.18-ac
 00:60:08:cd:18:62, IRQ 10
  product code 4b4b rev 00.0 date 12-09-97
  Internal config register is 16302d8, transceivers 0xe040.
  8K word-wide RAM 3:5 Rx:Tx split, autoselect/MII interface.
  MII transceiver found at address 24, status 786f.
  Enabling bus-master transmits and whole-frame receives.
00:13.0: scatter/gather enabled. h/w checksums disabled
eth0: Dropping NETIF_F_SG since no checksum feature.
PCI: Found IRQ 5 for device 00:14.0
See Documentation/networking/vortex.txt
00:14.0: 3Com PCI 3c905 Boomerang 100baseTx at 0xec00. Vers LK1.1.18-ac
 00:60:08:cd:17:b4, IRQ 5
  product code 4b4b rev 00.0 date 12-09-97
  Internal config register is 16302d8, transceivers 0xe040.
  8K word-wide RAM 3:5 Rx:Tx split, autoselect/MII interface.
  MII transceiver found at address 24, status 7849.
  Enabling bus-master transmits and whole-frame receives.
00:14.0: scatter/gather enabled. h/w checksums disabled
eth1: Dropping NETIF_F_SG since no checksum feature.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 96M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd8000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 Aperture @ 0xd8000000 64MB
[drm] Initialized radeon 1.7.0 20020828 on minor 1
[drm] AGP 0.99 Aperture @ 0xd8000000 64MB
[drm] Initialized i810 1.2.1 20020211 on minor 2
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: Maxtor 5T010H1, ATA DISK drive
hdb: CD-ROM 48X/AKU, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1hda: 19531250 sectors (10000 MB) w/2048KiB
Cache, CHS=2422/128/63
hdb: attached ide-cdrom driver.
hdb: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hda: [PTBL] [1215/255/63] hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11
hda12 >
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
ip_conntrack version 2.1 (1024 buckets, 8192 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 284k freed
Adding Swap: 64224k swap-space (priority -1)

>>>>>>>>>>>>>
lspci -vv

00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x]
(rev 44)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR-
 <PERR-
        Latency: 0
        Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 1.0
                Status: RQ=7 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
MVP3/Pro133x AGP] (prog-if 00 [N
ormal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR-
 <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev
12)
        Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB
2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR-
 <PERR-
        Latency: 0

00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
(prog-if 8a [Master SecP Pr
iP])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR-
 <PERR-
        Latency: 32
        Region 4: I/O ports at e000 [size=16]

00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management (rev
20)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR-
 <PERR-

00:0f.0 VGA compatible controller: S3 Inc. Trio 64V2/DX or /GX (rev 14)
(prog-if 00 [VGA])
        Subsystem: S3 Inc. 86C775 Trio64V2/DX, 86C785 Trio64V2/GX
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR-
 <PERR-
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=64M]
        Expansion ROM at <unassigned> [disabled] [size=64K]

00:13.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR-
 <PERR-
      Latency: 32 (750ns min, 2000ns max)
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at e800 [size=64]
        Expansion ROM at e1000000 [disabled] [size=64K]

00:14.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB
2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR-
 <PERR-
        Latency: 32 (750ns min, 2000ns max)
        Interrupt: pin A routed to IRQ 5
        Region 0: I/O ports at ec00 [size=64]
        Expansion ROM at e2000000 [disabled] [size=64K]


_______________________________________________
vortex mailing list
[email protected]
http://www.scyld.com/mailman/listinfo/vortex