Kernel error in 2.6.3

Hello all,

I finally got some time to work on my system again, and I got the wireless 
card (W200) working with Stephan Schulz's installation method on Mandrake10 
RC1.

I am however getting a strange error printed to dmesg every time the card 
powers up/down.

Is this a known bug? It dosent seem to do anything except freeze the system 
for about five seconds when the card is first powered up.

The card seems to work fine, even with the error. Should I post this as a bug?


dmesg:

usb 1-3: new full speed USB device using address 4
wlan0: Hardware identity 0008:0003:0001:0000
wlan0: Station identity  001f:0001:0008:003a
wlan0: Looks like a Lucent/Agere firmware version 8.58
wlan0: Ad-hoc demo mode supported
wlan0: IEEE standard IBSS ad-hoc mode supported
wlan0: WEP supported, 104-bit key
wlan0: MAC address 00:08:02:44:A8:04
wlan0: Station name "HERMES I"
wlan0: ready
/home/jeff/Downloads/laptop_install/wireless/driver_Cvs/orinoco/orinoco_usb.c: 
Orinoco USB device now attached wlan0
/home/jeff/Downloads/laptop_install/wireless/driver_Cvs/orinoco/orinoco_usb.c: 
bridge_access_ltv: in urb not pending
Badness in local_bh_enable at kernel/softirq.c:121
Call Trace:
 [<c01248a0>] local_bh_enable+0x59/0x70
 [<e1a6a277>] bridge_access_ltv+0x147/0x2bc [orinoco_usb]
 [<e1a6a540>] bridge_read_ltv+0x82/0x88 [orinoco_usb]
 [<e1a90ad5>] __orinoco_ev_info+0x430/0x44c [orinoco]
 [<e18622d0>] hcd_submit_urb+0x102/0x157 [usbcore]
 [<e1a6b2b5>] bridge_bulk_in_callback+0x244/0x328 [orinoco_usb]
 [<e18226a8>] td_free+0x65/0x6b [ohci_hcd]
 [<e1862820>] usb_hcd_giveback_urb+0x25/0x39 [usbcore]
 [<e18227f0>] finish_urb+0x69/0xed [ohci_hcd]
 [<e1823aa1>] dl_done_list+0xe1/0xe6 [ohci_hcd]
 [<e18243a3>] ohci_irq+0xa2/0x170 [ohci_hcd]
 [<e186286a>] usb_hcd_irq+0x36/0x67 [usbcore]
 [<c010d1a8>] handle_IRQ_event+0x3a/0x64
 [<c010d4b1>] do_IRQ+0x7b/0x111
 [<c0105000>] rest_init+0x0/0x27
 [<c010ba60>] common_interrupt+0x18/0x20
 [<c0105000>] rest_init+0x0/0x27
 [<c0109041>] default_idle+0x23/0x26
 [<c010909a>] cpu_idle+0x27/0x35
 [<c03d46cf>] start_kernel+0x163/0x191
 [<c03d4430>] unknown_bootoption+0x0/0x110

/home/jeff/Downloads/laptop_install/wireless/driver_Cvs/orinoco/orinoco_usb.c: 
Non specific state 2
/home/jeff/Downloads/laptop_install/wireless/driver_Cvs/orinoco/orinoco_usb.c: 
orinoco_usb: access failed(2) reply_count 48 (resetting)
/home/jeff/Downloads/laptop_install/wireless/driver_Cvs/orinoco/orinoco_usb.c: 
orinoco_usb: ctx failed
wlan0: New link status: Connected (0001)


Thanks,
Jeff Hagen
[email protected]