Re: CVS won't download firmware am I missing a step?

That worked to download the firmware, but here is what happens when I activate the card. These were my exact steps:
cd /path/to/orinoco
make
make install
cd firmware
sh get_ezusb_fw

then I rebooted, and tried to enable the card.  Here is the dmesg output:

 DMESG:

usb 2-3: new full speed USB device using address 2
orinoco 0.14alpha2HEAD (David Gibson <[email protected]>, Pavel Roskin <[email protected]>, et al)
Unable to handle kernel NULL pointer dereference at virtual address 00000032
 printing eip:
c0313d7d
*pde = 00000000
Oops: 0002 [#1]
CPU:    0
EIP:    0060:[<c0313d7d>]    Not tainted VLI
EFLAGS: 00010246
EIP is at hermes_init+0x37d/0x390
eax: 00000032   ebx: d2e68000   ecx: d2e682ec   edx: 00000000
esi: 00000000   edi: 00000000   ebp: d2e68000   esp: d2ef3da4
ds: 007b   es: 007b   ss: 0068
Process modprobe (pid: 5167, threadinfo=d2ef2000 task=c63b66b0)
Stack: 00000292 d2ef2000 ca7ad6c0 dda0f8bf 00000046 00000286 c0544c58 d2e68000 
       00000000 00000000 d2e68000 c0310134 d2e682ec 0000000a d2ef3e57 00000002 
       d2ef3e63 c02931bd d2ef3e57 d2ef3e63 d2e682ec d2e68220 0000000a ffffffff 
Call Trace:
 [<dda0f8bf>] bridge_req_ctx_wait+0xbf/0xd0 [orinoco_usb]
 [<c0310134>] orinoco_init+0x34/0x720
 [<c02931bd>] vsnprintf+0x23d/0x4a0
 [<c0119ec2>] __wake_up_locked+0x22/0x30
 [<c03fb34f>] register_netdevice+0x5f/0x2c0
 [<dda10cc7>] bridge_init+0xd7/0x180 [orinoco_usb]
 [<c03004d7>] register_netdev+0x57/0x90
 [<dda1180b>] bridge_probe+0x58b/0x8f0 [orinoco_usb]
 [<c0185580>] init_dir+0x0/0x20
 [<c0383b81>] usb_probe_interface+0x61/0x80
 [<c02e974f>] bus_match+0x3f/0x70
 [<c02e9879>] driver_attach+0x59/0x90
 [<c02e9b1d>] bus_add_driver+0x8d/0xa0
 [<c02e9f5f>] driver_register+0x2f/0x40
 [<c0383c5f>] usb_register+0x3f/0xa0
 [<dd9c7019>] bridge_module_init+0x19/0x7c [orinoco_usb]
 [<c0131bd5>] sys_init_module+0x105/0x1d0
 [<c048ae63>] syscall_call+0x7/0xb

Code: f1 d3 e0 66 c7 04 18 ff ff 8b 44 24 30 8b 78 04 8b 18 e9 e7 fc ff ff 8b 44 24 30 8b 48 08 b8 32 00 00 00 d3 e0 8b 4c 24 30 8b 11 <66> c7 04 10 00 00 8b 19 8b 71 08 8b 79 04 e9 a3 fc ff ff 55 57 


Then i must disable the device, and I get this:

<4>/root/orinoco/orinoco_usb.c: bridge_bulk_in_callback: urb timed out, not resubmiting
usb 2-3: USB disconnect, address 2


Have you seen this before?
> El dom, 14-03-2004 a las 18:45, [email protected] escribió:
> 
> > I downloaded the CVS, ran MAKE, then MAKE INSTALL  and no firmware was 
> downloaded as with other revisions...  Did I miss something?
> 
> cd cvs/orinoco/firmware/
> 
> sh get_ezusb_fw
> -- 
> Ramón Rey Vicente       <ramon dot rey at hispalinux dot es>
>         jabber ID       <rreylinux at jabber dot org>
> GPG public key ID       0xBEBD71D5 -> http://pgp.escomposlinux.org/
>