Re: Re: Matrox Millenium G450 AGP

On Sat, Apr 03, 2004 at 06:01:03PM +0200, Petr Vandrovec wrote:
> On Sat, Apr 03, 2004 at 03:41:18PM +0200, Sven Luther wrote:
> > On Sat, Apr 03, 2004 at 02:43:02PM +0200, Johan Gullden wrote:
> > > On Sat, 3 Apr 2004 13:51:25 +0200
> > > Johan Gullden <[email protected]> wrote:
> > > 
> > > > On Sat, 3 Apr 2004 12:49:42 +0200
> > > > Sven Luther <[email protected]> wrote:
> > > > 
> > > > > On Sat, Apr 03, 2004 at 12:32:54PM +0200, Johan Gullden wrote:
> > > > > > (I am not subscribed to the list, so please CC your replies to me.)
> > > > > > 
> > > > > > Hello,
> > > > > > 
> > > > > > I am having trouble getting my Matrox G450 to work on my pegasos2,
> > > > > > after and while booting the console gets weird. It doubles the output with a space of 4 characters, so it's really hard to use it.
> > > > > > 
> > > > > > The kernel I am using is 2.6.4 (gentoo/ppc-development-sources), I have also tried the 2.4 kernel and getting the same problems.
> > > > > > 
> > > > > > my settings from #Graphics support
> > > > > > 
> > > > > > CONFIG_FB=y
> > > > > > CONFIG_FB_MATROX=y
> > > > > > CONFIG_FB_MATROX_G450=y
> > > > > > CONFIG_FB_MATROX_G100=y
> > > > > > CONFIG_FB_MATROX_I2C=y
> > > > > > 
> > > > > > I have also tried to use diffrent boot parameters, but with no luck. The output is just a screen filled with colorful pixels.
> > > > > 
> > > > > Johan, could you provide a bit more detail about the screen. You told me
> > > > > that you saw like 4 different screens or soemthing such. This kind of
> > > > > information, or even a digicam picture of the screen, is essential in
> > > > > detecting the problem, and hopefully fixing it.
> > > > > 
> > > > 
> > > > Ok, there seems to be some missunderstanding, I will take a picture of the console. So you all can se waht I mean.
> > > > 
> > > 
> > > The pictures are really bad. But you should see what I mean.
> > > Pictures are visible at: http://hem.passagen.se/stimp
> > 
> > Nope, i don't understand what the problem is from those picutres, they
> > seem rather normal to me. I may be wrong though.
> 
> They are quite normal when using G100 in 2.4.x with weird memory chips. But
> it should not happen with 2.6.x which reads setup from ROM.

A G450 with 2.6.4 and 2.4.25, i think.

> (1) What is pegasos? Is it i386/x86_64/alpha architecture which executes/emulates ROM BIOS,
>     or is Matrox initialized only by matroxfb? Can you try 'video=matroxfb:init' or 'video=matroxfb:noinit'
>     options (default value is autodetect whether card was initialized or not; using noinit on
>     system which did not initialize matrox hardware may lock up PCI bus, so have reset button ready).

It is powerpc, using a standard x86 card, where the bios is run by an
emulator in the firmware.

> (2) If 'video=matroxfb:init' alone will not help, you can try playing with g450_memory_init() function.
>     It completely relies on PINS data, so if pins data are incorrect (like on GXT130P IBM distributed),
>     driver will not work without manual tweaking default_pins5() with values your hardware needs.

Mmm.

> (2a) Do you use card from Matrox, or is it some 3rd party product - either onboard (from f.e. HP) or
>      bundled with their own firmware (f.e. IBM)? Onboard devices are only in x86 systems, as in onboard
>      solutions there is usually no EEPROM connected to the graphics chip, and so it is not possible to 
>      find PINS structure.

Probably a Matrox board.

Friendly,

Sven Luther


-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials
Free Linux tutorial presented by Daniel Robbins, President and CEO of
GenToo technologies. Learn everything from fundamentals to system
administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click