Re: ATI support

Ok, I polished and modified it a bit, now backup your older xorg.conf 
and try with the attached one. Then reboot, and issue this command in a 
terminal: fglrxinfo
If your output is something like this, you're done:
display: :0.0  screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: RADEON XPRESS Series
OpenGL version string: 2.0.6334 (8.34.8)

If after this all you don't have 3D yet, please attach your 
/var/log/Xorg.0.log file to the answer.

Dario

Mike Chambers ha scritto:
> On Tue, 2007-03-20 at 22:30 +0100, Dario Castellarin wrote:
>   
>> Can you please attach your xorg.conf and Xorg.0.log?
>> Mike Chambers ha scritto:
>>     
>>> On Tue, 2007-03-20 at 11:51 -0500, Justin Conover wrote:
>>>
>>>   
>>>       
>>>> After you install the driver, run the following:
>>>>
>>>>  yum install ati-x11-drv
>>>> aticonfig --initial
>>>> aticonfig --overlay-type=Xv
>>>> edit xorg.conf and drop in the bottom
>>>>
>>>> Section "Extensions"
>>>>         Option  "Composite" "Disable"
>>>> EndSection
>>>>
>>>> Section "ServerFlags"
>>>>         Option  "AIGLX" "off"
>>>> EndSection
>>>>     
>>>>         
>>> After doing the above, and also even adding a dri section as well as a
>>> Load dri in the module section, this is what I get below when running
>>> glxgears..
>>>
>>> [mike@scrappy ~]$ glxgears
>>> Xlib:  extension "XFree86-DRI" missing on display ":0.0".
>>> 1696 frames in 5.2 seconds = 327.441 FPS
>>>
>>> Do I need to reboot again or is restarting xfs good enough?
>>>       
>
> Ok, here is my config file.  And in case I forgot or never mentioned
> this, the card is a radeon X1300.
>
> What I did see in the .conf file, was there were now two device sections
> after the aticonfig --initial command.  One section has vesa, one has
> fglrx.  Also, when trying to enable desktop effects, it tells me
> composite extension is not available.
>
>   
> ------------------------------------------------------------------------
>
> # Xorg configuration created by system-config-display
>
> Section "ServerLayout"
> 	Identifier     "single head configuration"
> 	Screen      0  "aticonfig-Screen[0]" 0 0
> 	InputDevice    "Keyboard0" "CoreKeyboard"
> EndSection
>
> Section "Files"
> EndSection
>
> Section "Module"
> EndSection
>
> Section "InputDevice"
> 	Identifier  "Keyboard0"
> 	Driver      "kbd"
> 	Option	    "XkbModel" "pc105"
> 	Option	    "XkbLayout" "us"
> EndSection
>
> Section "Monitor"
>
>  ### Comment all HorizSync and VertSync values to use DDC:
>  ### Comment all HorizSync and VertSync values to use DDC:
> 	Identifier   "Monitor0"
> 	ModelName    "KDS XFlat XF-9b/XF-9c/XF-9e/XF-9p"
> 	HorizSync    30.0 - 98.0
> 	VertRefresh  50.0 - 160.0
> 	Option	    "dpms"
> EndSection
>
> Section "Monitor"
> 	Identifier   "aticonfig-Monitor[0]"
> 	Option	    "VendorName" "ATI Proprietary Driver"
> 	Option	    "ModelName" "Generic Autodetecting Monitor"
> 	Option	    "DPMS" "true"
> EndSection
>
> Section "Device"
> 	Identifier  "Videocard0"
> 	Driver      "vesa"
> EndSection
>
> Section "Device"
> 	Identifier  "aticonfig-Device[0]"
> 	Driver      "fglrx"
> EndSection
>
> Section "Screen"
> 	Identifier "Screen0"
> 	Device     "Videocard0"
> 	Monitor    "Monitor0"
> 	DefaultDepth     24
> 	SubSection "Display"
> 		Viewport   0 0
> 		Depth     24
> 		Modes    "1280x1024" "1280x960" "1280x800" "1152x864" "1152x768" "1024x768" "800x600" "640x480"
> 	EndSubSection
> EndSection
>
> Section "Screen"
> 	Identifier "aticonfig-Screen[0]"
> 	Device     "aticonfig-Device[0]"
> 	Monitor    "aticonfig-Monitor[0]"
> 	DefaultDepth     24
> 	SubSection "Display"
> 		Viewport   0 0
> 		Depth     24
> 	EndSubSection
> EndSection
>
> Section "Extensions"
>          Option  "Composite" "Disable"
> EndSection
>
> Section "ServerFlags"
>          Option  "AIGLX" "off"
> EndSection
>

# Xorg configuration created by system-config-display

Section "ServerLayout"
	Identifier     "single head configuration"
	Screen      0  "aticonfig-Screen[0]" 0 0
	InputDevice    "Keyboard0" "CoreKeyboard"
EndSection


Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "kbd"
	Option	    "XkbModel" "pc105"
	Option	    "XkbLayout" "us"
EndSection


Section "Monitor"
	Identifier   "aticonfig-Monitor[0]"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
EndSection


Section "Device"
	Identifier  "aticonfig-Device[0]"
	Driver      "fglrx"
	Option	    "VideoOverlay" "on"
EndSection


Section "Screen"
	Identifier "aticonfig-Screen[0]"
	Device     "aticonfig-Device[0]"
	Monitor    "aticonfig-Monitor[0]"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "Extensions"
         Option  "Composite" "Disable"
EndSection

Section "ServerFlags"
         Option  "AIGLX" "off"
EndSection