live cd 2005.0-r4 on iMac G5
Holger Amann <[email protected]>
| Newsgroups | gmane.linux.gentoo.ppc |
|---|---|
| Message-ID | <[email protected]> |
Hi, I've tested live cd 2005.0-r4 and after a few lines of kernel messages the display became black. The last line I saw was something with "smp_cXX". But the system was still alive because I was able to bring up ethernet and sshd by typing sightlessly. It's an iMac G5 1.8 GHz from october 2004 Found initrd at 0xc000000001d00000:0xc000000001de8c0a trying to initialize btext ... U3-DART: table not allocated, using direct DMA Starting Linux PPC64 2.6.12-gentoo-livecd ----------------------------------------------------- ppc64_pft_size = 0x18 ppc64_debug_switch = 0x0 ppc64_interrupt_controller = 0x1 systemcfg = 0xc000000000554000 systemcfg->platform = 0x400 systemcfg->processorCount = 0x1 systemcfg->physicalMemorySize = 0x30000000 ppc64_caches.dcache_line_size = 0x80 ppc64_caches.icache_line_size = 0x80 htab_address = 0xc00000002e000000 htab_hash_mask = 0x1ffff ----------------------------------------------------- [boot]0100 MM Init [boot]0100 MM Init Done Linux version 2.6.12-gentoo-livecd (root@G5) (gcc version 3.4.3 20041125 (Gentoo Linux 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #1 SMP Thu Jun 23 11:23:27 UTC 2005 [boot]0012 Setup Arch Syscall map setup, 229 32 bits and 205 64 bits syscalls Found U3 memory controller & host bridge, revision: 57 Mapped at 0xe000000080152000 Found a K2 mac-io controller, rev: 0, mapped at 0xe000000080193000 PowerMac motherboard: iMac G5 nvram: Checking bank 0... nvram: gen0=52, gen1=51 nvram: Active bank is: 0 Adding PCI host bridge /pci@0,f0000000 Found U3-AGP PCI host bridge. Firmware bus number: 240->255 Adding PCI host bridge /ht@0,f2000000 Can't get bus-range for /ht@0,f2000000, assume bus 0 U3/HT: hole, 0 end at 8fffffff, 1 start at b0000000 Found U3-HT PCI host bridge. Firmware bus number: 0->239 Can't get bus-range for /ht@0,f2000000 PCI Host 0, io start: fffffffffd800000; io end: fffffffffdffffff PCI Host 1, io start: 0; io end: 3fffff Using native/NAP idle loop Top of RAM: 0x30000000, Total RAM: 0x30000000 Memory hole size: 0MB On node 0 totalpages: 196608 DMA zone: 196608 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 [boot]0015 Setup Done Built 1 zonelists Kernel command line: root=/dev/ram rw ramdisk_size=11000 cdroot devfs init=/linuxrc PowerMac using OpenPIC irq controller at 0x80040000 mpic: Setting up MPIC " K2-MPIC " version 1.2 at 80040000, max 4 CPUs mpic: ISU size: 124, shift: 7, mask: 7f mpic: Initializing for 124 sources Slave OpenPIC at 0xf8040000 hooked on IRQ 96 mpic: Setting up MPIC " U3-MPIC " version 1.2 at f8040000, max 4 CPUs mpic: ISU size: 124, shift: 7, mask: 7f mpic: Initializing for 124 sources PID hash table entries: 4096 (order: 12, 131072 bytes) time_init: decrementer frequency = 33.333333 MHz SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 46 => 0 (71) Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 748156k/786432k available (4388k kernel code, 37552k reserved, 1664k data, 442k bss, 340k init) Calibrating delay loop... 66.30 BogoMIPS (lpj=33152) Mount-cache hash table entries: 256 PowerMac SMP probe found 1 cpus Brought up 1 CPUs CPU0 attaching sched-domain: domain 0: span 1 groups: 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 931k freed NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Probing PCI hardware done SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub i/pSeries Real Time Clock Driver v1.1 nvram_init: Could not find nvram partition for nvram buffered error logging. Total HugeTLB memory allocated, 0 inotify device minor=63 devfs: 2004-01-31 Richard Gooch ([email protected]) devfs: boot_options: 0x1 Installing knfsd (copyright (C) 1996 [email protected]). JFS: nTxBlock = 5857, nTxLock = 46863 Initializing Cryptographic API rivafb: nVidia device/chipset 10DE0329 rivafb: nVidia Corporation NV34M [GeForce FX Go5200] rivafb: On a laptop. Assuming Digital Flat Panel rivafb: Detected CRTC controller 1 being used rivafb: disabling acceleration rivafb: setting virtual Y resolution to 46603 Console: switching to colour frame buffer device 180x56 rivafb: PCI nVidia NV32 framebuffer ver 0.9.5b (64MB @ 0xA0000000) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 11000K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 6.0.54-k2 Copyright (c) 1999-2004 Intel Corporation. sungem.c:v0.98 8/24/03 David S. Miller ([email protected]) PHY ID: 4061e4, addr: 0 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:59:84:b4 eth0: Found BCM5221 PHY MacIO PCI driver attached to K2 chipset Warning: no ADB interface detected Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PCI: Enabling device: (0001:02:0d.0), cmd 2 ide0: Found Apple Shasta ATA-6 controller, bus ID 3, irq 38 Probing IDE interface ide0... hda: MATSHITADVD-R UJ-825, ATAPI CD/DVD-ROM drive hda: Enabling Ultra DMA 4 ide0 at 0xe00000008802c000-0xe00000008802c007,0xe00000008802c160 on irq 38 hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide libata version 1.11 loaded. sata_svw version 1.05 ata1: SATA max UDMA/133 cmd 0xE00000008802E000 ctl 0xE00000008802E020 bmdma 0xE00000008802E030 irq 10 ata2: SATA max UDMA/133 cmd 0xE00000008802E100 ctl 0xE00000008802E120 bmdma 0xE00000008802E130 irq 10 ata3: SATA max UDMA/133 cmd 0xE00000008802E200 ctl 0xE00000008802E220 bmdma 0xE00000008802E230 irq 10 ata4: SATA max UDMA/133 cmd 0xE00000008802E300 ctl 0xE00000008802E320 bmdma 0xE00000008802E330 irq 10 ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:007f ata1: dev 0 ATA, max UDMA/133, 156301488 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_svw ata2: no device found (phy stat 00000004) scsi1 : sata_svw ata3: no device found (phy stat 00000000) scsi2 : sata_svw ata4: no device found (phy stat 00000000) scsi3 : sata_svw Vendor: ATA Model: ST380013AS Rev: 5.06 Type: Direct-Access ANSI SCSI revision: 05 st: Version 20050312, fixed bufsize 32768, s/g segs 256 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) SCSI device sda: drive cache: write back SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) SCSI device sda: drive cache: write back /dev/scsi/host0/bus0/target0/lun0: [mac] p1 p2 p3 p4 p5 p6 p7 p8 p9 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1250 $ Ben Collins <[email protected]> PCI: Enabling device: (0001:02:0e.0), cmd 2 ohci1394: fw-host0: Unexpected PCI resource length of 1000! ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[39] MMIO= [80100000-801007ff] Max Packet=[2048] ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugs is not available PCI: Enabling device: (0001:01:0b.2), cmd 6 ehci_hcd 0001:01:0b.2: NEC Corporation USB 2.0 ehci_hcd 0001:01:0b.2: new USB bus registered, assigned bus number 1 ehci_hcd 0001:01:0b.2: irq 70, io mem 0x80080000 ehci_hcd 0001:01:0b.2: park 0 ehci_hcd 0001:01:0b.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) PCI: Enabling device: (0001:01:0b.0), cmd 2 ohci_hcd 0001:01:0b.0: NEC Corporation USB ohci_hcd 0001:01:0b.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:01:0b.0: irq 70, io mem 0x80082000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected PCI: Enabling device: (0001:01:0b.1), cmd 2 ohci_hcd 0001:01:0b.1: NEC Corporation USB (#2) ohci_hcd 0001:01:0b.1: new USB bus registered, assigned bus number 3 ohci_hcd 0001:01:0b.1: irq 70, io mem 0x80081000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usb 2-1: new full speed USB device using ohci_hcd and address 2 hub 2-1:1.0: USB hub found hub 2-1:1.0: 3 ports detected usbcore: registered new driver usb-storage USB Mass Storage support registered. ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d93fffe5984b4] usb 3-1: new low speed USB device using ohci_hcd and address 2 usbcore: registered new driver hiddev input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:01:0b.1-1 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice i2c /dev entries driver Found KeyWest i2c on "u3", 2 channels, stepping: 4 bits Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 2032.000 MB/sec 8regs_prefetch: 1644.000 MB/sec 32regs : 2372.000 MB/sec 32regs_prefetch: 1984.000 MB/sec raid5: using function: 32regs (2372.000 MB/sec) md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected] oprofile: using ppc64/970 performance monitoring. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 64Kbytes TCP established hash table entries: 131072 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) IPv4 over IPv4 tunneling driver ip_conntrack version 2.1 (3072 buckets, 24576 max) - 304 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost <[email protected]>. http:// snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 1 NET: Registered protocol family 17 devfs_mk_dev: could not append to parent for md/0 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 usb 2-1.2: new full speed USB device using ohci_hcd and address 3 VFS: Mounted root (ext2 filesystem). Mounted devfs on /dev Freeing unused kernel memory: 340k freed usb 2-1.3: new full speed USB device using ohci_hcd and address 4 input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:01:0b.0-1.3 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:01:0b.0-1.3 VFS: Can't find ext3 filesystem on dev hda. VFS: Can't find an ext2 filesystem on dev hda. cramfs: wrong magic FAT: bogus number of reserved sectors VFS: Can't find a valid FAT filesystem on dev hda. FAT: bogus number of reserved sectors VFS: Can't find a valid FAT filesystem on dev hda. ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 18 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 18 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 19 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 19 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 19 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 19 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 19 => 0 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 8e len=1 81 => -1 (71) SMU do_cmd 8e len=1 81 SMU do_cmd 71 len=7 19 => 0 (71) usb 1-3: new high speed USB device using ehci_hcd and address 4 scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning Vendor: USB 2.0 Model: Mobile Disk Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 02 sdb: Unit Not Ready, sense: : Current: sense key: Unit Attention Additional sense: Not ready to ready change, medium may have changed SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: Write Protect is off sdb: Mode Sense: 03 00 00 00 sdb: assuming drive cache: write through SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: Write Protect is off sdb: Mode Sense: 03 00 00 00 sdb: assuming drive cache: write through /dev/scsi/host4/bus0/target0/lun0: p1 Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0 Attached scsi generic sg1 at scsi4, channel 0, id 0, lun 0, type 0 usb-storage: device scan complete VFS: Can't find ext3 filesystem on dev sda1. usb 1-3: USB disconnect, address 4 usb 1-3: new high speed USB device using ehci_hcd and address 5 scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning Vendor: USB 2.0 Model: Mobile Disk Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 02 sdb: Unit Not Ready, sense: : Current: sense key: Unit Attention Additional sense: Not ready to ready change, medium may have changed SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: Write Protect is off sdb: Mode Sense: 03 00 00 00 sdb: assuming drive cache: write through SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: Write Protect is off sdb: Mode Sense: 03 00 00 00 sdb: assuming drive cache: write through /dev/scsi/host5/bus0/target0/lun0: p1 Attached scsi removable disk sdb at scsi5, channel 0, id 0, lun 0 Attached scsi generic sg1 at scsi5, channel 0, id 0, lun 0, type 0 usb-storage: device scan complete VFS: Can't find ext3 filesystem on dev sda1. 0000:f0:0b.0 Host bridge: Apple Computer Inc. U3L AGP Bridge Flags: bus master, 66Mhz, medium devsel, latency 16 Capabilities: [80] AGP version 3.0 0000:f0:10.0 VGA compatible controller: nVidia Corporation NV34M [GeForce FX Go5200] (rev a1) (prog-if 00 [VGA]) Subsystem: nVidia Corporation: Unknown device 0010 Flags: bus master, 66Mhz, medium devsel, latency 16, IRQ 59 Memory at 91000000 (32-bit, non-prefetchable) [size=90000000] Memory at a0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at 00020000 [disabled] Capabilities: [60] Power Management version 2 Capabilities: [44] AGP version 3.0 0001:00:01.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog- if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 Memory behind bridge: 80200000-805fffff Prefetchable memory behind bridge: 00000000-000fffff Capabilities: [70] #08 [0061] Capabilities: [90] #08 [8000] 0001:00:02.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog- if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 Memory behind bridge: 80000000-800fffff Prefetchable memory behind bridge: 00000000-000fffff Capabilities: [70] #08 [8824] 0001:00:03.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog- if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 Memory behind bridge: 80100000-801fffff Prefetchable memory behind bridge: 00000000-000fffff Capabilities: [70] #08 [8824] 0001:01:01.0 Network controller: Broadcom Corporation BCM4306 802.11b/ g Wireless LAN Controller (rev 03) Subsystem: Apple Computer Inc.: Unknown device 004e Flags: bus master, fast devsel, latency 16, IRQ 60 Memory at 80084000 (32-bit, non-prefetchable) [disabled] Capabilities: [40] Power Management version 2 0001:01:07.0 Class ff00: Apple Computer Inc. Shasta Mac I/O Flags: bus master, medium devsel, latency 16 Memory at 80000000 (32-bit, non-prefetchable) 0001:01:0b.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) Subsystem: NEC Corporation USB Flags: bus master, medium devsel, latency 16, IRQ 70 Memory at 80082000 (32-bit, non-prefetchable) Capabilities: [40] Power Management version 2 0001:01:0b.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) Subsystem: NEC Corporation USB Flags: bus master, medium devsel, latency 16, IRQ 70 Memory at 80081000 (32-bit, non-prefetchable) Capabilities: [40] Power Management version 2 0001:01:0b.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog- if 20 [EHCI]) Subsystem: NEC Corporation USB 2.0 Flags: bus master, medium devsel, latency 16, IRQ 70 Memory at 80080000 (32-bit, non-prefetchable) Capabilities: [40] Power Management version 2 0001:02:0c.0 IDE interface: Broadcom (formerly ServerWorks) K2 SATA (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Broadcom (formerly ServerWorks) K2 SATA Flags: bus master, 66Mhz, medium devsel, latency 16, IRQ 10 I/O ports at <unassigned> [disabled] I/O ports at <unassigned> [disabled] I/O ports at <unassigned> [disabled] I/O ports at <unassigned> [disabled] I/O ports at <unassigned> [disabled] Memory at 80102000 (32-bit, non-prefetchable) [size=8K] 0001:02:0d.0 Class ff00: Apple Computer Inc. Shasta IDE Flags: bus master, medium devsel, latency 32, IRQ 38 Memory at 80104000 (32-bit, non-prefetchable) 0001:02:0e.0 FireWire (IEEE 1394): Apple Computer Inc. Shasta Firewire (prog-if 10 [OHCI]) Subsystem: Apple Computer Inc.: Unknown device 5811 Flags: bus master, medium devsel, latency 248, IRQ 39 Memory at 80100000 (32-bit, non-prefetchable) Capabilities: [44] Power Management version 2 0001:03:0f.0 Ethernet controller: Apple Computer Inc. Shasta (Sun GEM) Flags: bus master, 66Mhz, slow devsel, latency 16, IRQ 40 Memory at 80400000 (32-bit, non-prefetchable) [size=80200000] Expansion ROM at 00100000 [disabled]