RE: Installation problems

I also thought that haresources only has 1 entry .. The primary server
with the daemon running on it.. And the other 3rd conf file has the
information for the failover file... No ???? 

-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Robert
Bates
Sent: Thursday, August 11, 2005 1:21 PM
To: [email protected]
Subject: Re: Installation problems

Hello Simone,

I checked but the server names is ha.cf where correct.  I have attached
my haresources and ha.cf files if you wouldn't mind taking a look.

Robert


----- Original Message -----
From: "Simone Segato" <[email protected]>
To: <[email protected]>
Sent: Thursday, August 11, 2005 12:13 PM
Subject: Re: Installation problems


> Hello Robert,
>
> Type uname -n on both LVS nodes.  The result you get back in the node
> name for you system.  You have to specify this name in the ha.cf file
> about half way down.  You will notice there is an entry in the
template
> ha.cf file that reads:
>
> node   kathy
>
> Replace kathy with your node name.
>
> Hope that works for you.
>
> Simone.
>
> Robert Bates wrote:
>
> >I added  IPaddr2::192.168.0.100/24/eth0 and
IPaddr2::192.168.0.200/24/eth0
> >to haresources and now I get a bad node name error.
> >
> >----- Original Message ----- 
> >From: "Horms" <[email protected]>
> >To: <[email protected]>
> >Sent: Thursday, August 11, 2005 1:14 AM
> >Subject: Re: Installation problems
> >
> >
> >
> >
> >>On Wed, Aug 10, 2005 at 07:35:16PM -0700, Robert Bates wrote:
> >>
> >>
> >>>Hi Simone and Rick,
> >>>
> >>>I found problem number 2.  I did something wrong with the loopback
which
> >>>killed network and generated the IP conflict errors but removed
them
and
> >>>
> >>>
> >now
> >
> >
> >>>at least they can see the network.
> >>>
> >>>On problem 1 I don't have the virtual IPs in haresources.  For some
> >>>
> >>>
> >reason I
> >
> >
> >>>can't seem to get the syntax right because it keeps throwing
errors.
> >>>
> >>>
> >This
> >
> >
> >>>is what I have
> >>>
> >>>192.168.0.100  virtual web server
> >>>192.168.0.101  real web server 1
> >>>192.168.0.102  real web server 2
> >>>
> >>>192.168.0.200  virtual mysql server
> >>>192.168.0.201  real mysql server 1
> >>>192.168.0.202  real mysql server 2
> >>>
> >>>
> >>to your haresourses should add this.
> >>
> >>
> >>To elaborate slightly on ip vs ifconfig, which came up in another
mail.
> >>
> >>ifconfig is the old-school way of configuring interfaces. It along
with
> >>route is what the IPaddr resource uses. This works, mostly, but it
turns
> >>out that ifconfig is not very well suited to this kind of work for a
> >>variety of reasons. IPaddr2 is a reimlimentation of IPaddr which
makes
> >>use if the ip command, and as a result is a lot cleaner, and
provides
> >>some features that are either impossible, or to complex to provide
using
> >>IPaddr.
> >>
> >>For your purposes either should do, the syntax is the same.
> >>But IPaddr2 is the way of the future, so I recommend using that.
> >>
> >>ip is a more powerful tool that allows you to configure interfaces,
> >>routing, policy routing, and all sorts of other fun stuff.
> >>As mentioned above, this is what IPaddr2 uses.
> >>
> >>The main catch is that the model that ifconfig uses to add
additional
> >>addresses to an interface - called an alias - basically sets up a
> >>separate virtual interface. Whereas ip just adds a secondary address
to
> >>the interface. This is important because while ip can see aliases
set up
> >>using ifconfig, ifconfig can't see secondary addresses added using
ip.
> >>
> >>So if you use ifconfig (which lets face it is a bit easier to type,
> >>especially if you have been using it for years) and you think
> >>there are some addresses missing, double check using ip addr sh
> >>
> >>-- 
> >>Horms
> >>
> >>
> >>-- 
> >>Ultra Monkey - http://www.ultramonkey.org/
> >>To UNSUBSCRIBE, email to [email protected], with a body:
> >>unsubscribe ultramonkey-users [email protected]
> >>where "[email protected]" is YOUR email address.
> >>
> >>
> >>
>
>
> -- 
> Ultra Monkey - http://www.ultramonkey.org/
> To UNSUBSCRIBE, email to [email protected], with a body:
> unsubscribe ultramonkey-users [email protected]
> where "[email protected]" is YOUR email address.
>
>


-- 
Ultra Monkey - http://www.ultramonkey.org/
To UNSUBSCRIBE, email to [email protected], with a body:
unsubscribe ultramonkey-users [email protected]
where "[email protected]" is YOUR email address.