Re: Antw: How to modify crm configure by command line

Hi!

BTW, I have a question: What is the difference of crm configure load replace
<file> and using crm configure edit (and replace the contents in the editor
with <file>)? I had a case where the first method showed many errors while the
second version worked. And: <file> was created by crm configure save <file>.

Regards,
Ulrich

>>> "Dang Zhiqiang" <[email protected]> schrieb am 29.07.2014 um 05:53 in
Nachricht
<[email protected]>:
> Thank you.
> My pacemaker version is 1.0.13, don't have filter subcommand, 
> but I think I will implement this function by "delete resource and create 
> same resoure", although doing it more complex, because I need it.
> 
> 
> 
> At 2014-07-28 06:10:56, "Kristoffer Grönlund" <[email protected]> wrote:
>>On Mon, 28 Jul 2014 17:45:44 +0800 (CST)
>>"Dang Zhiqiang" <[email protected]> wrote:
>>
>>> thanks,
>>> I know this method, but I want to modify it by command line, provides
>>> an interface for other user.
>>> 
>>
>>This is a bit of a hack, but you can achieve this with the filter
>>command:
>>
>>crm configure filter "sed '/op start/s/60s/600s/'" test-ip
>>
>>It would probably be good to have an update mode for the configure
>>commands so that crm configure primitive could make changes like these,
>>I will see about adding it in future versions.
>>
>>// Kristoffer
>>
>>> 
>>> 
>>> At 2014-07-28 05:25:15, "Ulrich Windl"
>>> <[email protected]> wrote:
>>> >>>> "Dang Zhiqiang" <[email protected]> schrieb am 28.07.2014 um 11:18
>>> >>>> in Nachricht
>>> ><[email protected]>:
>>> >> hi,
>>> >> I want to modify op start timeout value through command line, but
>>> >> I search on internet find nothing.
>>> >> I try crm_resource  comand, but I only modify params and meta.
>>> >> 
>>> >> 
>>> >> root@host2:~# crm configure show test-ip
>>> >> primitive test-ip ocf:openindiana:IPaddr \
>>> >>         params ip="192.168.1.253" nic="igb0" cidr_netmask="24" \
>>> >>         op start interval="0s" timeout="60s" on-fail="restart" \
>>> >>         op monitor interval="10s" timeout="60s" on-fail="restart" \
>>> >>         op stop interval="0s" timeout="60s" on-fail="stop" \
>>> >>         meta target-role="Stopped"
>>> >
>>> >"crm configure edit test-ip"?
>>> >
>>> >> 
>>> >> _______________________________________________
>>> >> Linux-HA mailing list
>>> >> [email protected] 
>>> >> http://lists.linux-ha.org/mailman/listinfo/linux-ha 
>>> >> See also: http://linux-ha.org/ReportingProblems 
>>> >
>>> >
>>> >
>>> >_______________________________________________
>>> >Linux-HA mailing list
>>> >[email protected] 
>>> >http://lists.linux-ha.org/mailman/listinfo/linux-ha 
>>> >See also: http://linux-ha.org/ReportingProblems 
>>> _______________________________________________
>>> Linux-HA mailing list
>>> [email protected] 
>>> http://lists.linux-ha.org/mailman/listinfo/linux-ha 
>>> See also: http://linux-ha.org/ReportingProblems 
>>> 
>>
>>
>>
>>-- 
>>// Kristoffer Grönlund
>>// [email protected] 
> 
> 
> _______________________________________________
> Linux-HA mailing list
> [email protected] 
> http://lists.linux-ha.org/mailman/listinfo/linux-ha 
> See also: http://linux-ha.org/ReportingProblems 


_______________________________________________
Linux-HA mailing list
[email protected]
http://lists.linux-ha.org/mailman/listinfo/linux-ha
See also: http://linux-ha.org/ReportingProblems