Re: "MPH_DEACTIVATE_IND" message....

Hi Karsten!
Thanks for your response.

The crazy thing at the whole thing is the following, even if I follow
your instructions the message is always the same:

I tested the cable which is fine, the operator confirmed me that it's
capable sending me a signal to the NT unit.

I have an active ISDN line connected with a numberblock (PTP), and I am
not getting smart :(

I have opened 2 shells, one with misdn_log -c0 and the other with
misdntestcon -0 -n 7985442

doug@home:/tmp# misdntestcon -c0 -n 7985442
TestmISDN 1.0
got DL_INFORMATION_IND
got unexpected MPH_DEACTIVATE_IND (602) message
got unexpected DL_RELEASE_IND (1108) message
select timeeout
do_setup error 10


misdn_log resultset:

misdn_log -c0
mISDN kernel version 1.01.29 found
mISDN user   version 1.01.31 found
4 controllers found
    id:        0
    Dprotocols:    00000006
    Bprotocols:    0000006e
    protocol:    1
    channelmap:    00000000000000000000000000000006
    nrbchan:    2
    name:        hfc-4s.1-1
log bind ch(0) return 0
Echo channel logging no
04.03.2014 21:31:15.482524 ACTIVATE REQ id=00017f00
04.03.2014 21:31:22.496883 DEACTIVATE IND id=0000ffff



What could be causing this problem?!
What does this error message tell me?


I have added you further infos, in case you have any more ideas.

Thank you very much for your response!


Thank you for your help and response


Doug





here is my board:

Found 4 ports
  Port  0 'hfc-4s.1-1':      TE/NT-mode BRI S/T (for phone lines & phones)
                              2 B-channels: 1-2
                                B-protocols: RAW HDLC X75slp L2:DSP
L2:DSPHDLC
  --------
  Port  1 'hfc-4s.1-2':      TE/NT-mode BRI S/T (for phone lines & phones)
                              2 B-channels: 1-2
                                B-protocols: RAW HDLC X75slp L2:DSP
L2:DSPHDLC
  --------
  Port  2 'hfc-4s.1-3':      TE/NT-mode BRI S/T (for phone lines & phones)
                              2 B-channels: 1-2
                                B-protocols: RAW HDLC X75slp L2:DSP
L2:DSPHDLC
  --------
  Port  3 'hfc-4s.1-4':      TE/NT-mode BRI S/T (for phone lines & phones)
                              2 B-channels: 1-2
                                B-protocols: RAW HDLC X75slp L2:DSP
L2:DSPHDLC

misdnportinfo:

Found 4 devices
        id:             0
        Dprotocols:     00000006
        Bprotocols:     0000006e
        protocol:       1
        nrbchan:        2
        name:           hfc-4s.1-1
        id:             1
        Dprotocols:     00000006
        Bprotocols:     0000006e
        protocol:       0
        nrbchan:        2
        name:           hfc-4s.1-2
        id:             2
        Dprotocols:     00000006
        Bprotocols:     0000006e
        protocol:       0
        nrbchan:        2
        name:           hfc-4s.1-3
        id:             3
        Dprotocols:     00000006
        Bprotocols:     0000006e
        protocol:       0
        nrbchan:        2
        name:           hfc-4s.1-4



Am 04.03.2014 20:59, schrieb Karsten Keil:
> misdntestcon -c0 -n 12