Success with driverloader and Dell True Mobil 1300 But...

Hi

Well it seems a manual shell command as root ## ifup wlan0    activates the card.
Now I am conected to ping the router and use the internet and Local net.
I am happy with the results.
Just two questions.
 1 .. What do I do to activate ifup wlan0 on Boot? I find no ifcfg-wlan0 script.
       Where is it do I write one, if so an example please 
 2.. What utilities can I use to see Signal power Graphically and to pick up another router on which I am allowed and in Range of as I only entered One ESSID.
 Or is this Automatic?
My INFO AS OF IFDOWN wlan0 & IFUP wlan0
   the xxx and iii in my ips are for my security on the mail list.

ifdown wlan0
    wlan0     device: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
linux:/home/bobby # ifup wlan0
    wlan0     device: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
    wlan0     warning: using NO encryption
Starting DHCP Client Daemon on wlan0... . . . . . IP/Netmask: 192.168.xxx.iii / 255.255.255.0
ERROR: Warning: Could not set up default route via interface
       Command ip route replace to default via 198.168.xxx.xxx returned:
       . RTNETLINK answers: Network is unreachable
       Configuration line: default 198.168.xxx.xxx - -
       This needs NOT to be AN ERROR if you set up multiple interfaces.
       See man 5 routes how to avoid this warning.

*********************************************
My INFO BEFORE IFDOWN wlan0 & IFUP wlan0

linux:/home/bobby # iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11-DS  ESSID:"USR8022"  Nickname:"unknown"
          Mode:Managed  Frequency:2.462 GHz  Access Point: 00:C0:49:A6:68:1B
          Bit Rate=11 Mb/s   Tx-Power=25 dBm
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=3/94  Signal level=-78 dBm  Noise level=-154 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:353   Missed beacon:0

eth1      no wireless extensions.

sit0      no wireless extensions.

linux:/home/bobby # dmesg
Linux version 2.6.11.4-21.9-default (geeko@buildhost) (gcc version 3.3.5 2005011
7 (prerelease) (SUSE Linux)) #1 Fri Aug 19 11:58:59 UTC 2005


SECTION of dmesg that applies to Wan card
++++++++++++++++++++++++++++++++++++++++++

eth0: Broadcom 4400 10/100BaseT Ethernet 00:0b:db:9d:0f:dd
driverloader: no version for "struct_module" found: kernel tainted.
driverloader: module license 'see LICENSE file; Copyright (c)2003-2004 Linuxant
inc.' taints kernel.
driverloader: stack=8192/60/0 REGPARM
usbcore: registered new driver driverloader
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: excluding 0x8e0-0x8e7
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
driverloader: bcmwl5.sys: 0xf9326000..0xf9380180 entry = f9331dd2 (pbase = 0x100
00)
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
0000:02:02.0: cache line size not set; forcing 32
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xa00-0xaff: clean.
wlan0: New link status: Disconnected (0002)
wlan0: WPA, AES, TKIP, WEP128, WEP64 supported
wlan0: at 0000:02:02.0 (MAC address 00:90:4B:28:79:6F) ready
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
PCI: Enabling device 0000:03:00.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:03:00.0 to 64
tulip0:  MII transceiver #1 config 3100 status 7849 advertising 05e1.
eth1: ADMtek Comet rev 17 at 00014000, 00:0F:B5:45:D3:AE, IRQ 11.
NET: Registered protocol family 17
st: Version 20041025, fixed bufsize 32768, s/g segs 256
wlan0: New link status: Connected (0001)
Non-volatile memory driver v1.2

_______________________________________________
driverloader mailing list
[email protected]
https://www.linuxant.com/mailman/listinfo/driverloader