Belkin F5D7050 Device not detected

Hi List,

I am having a problem with my Belkin F5D7050 USB adaptor. I hope someone here can give me some advice on what to do.

I have installed the driverloader kernel module successfully and
afterwards ran the web configuration tool and uploaded the windows
drivers.

The problem is that the web config then informs me that my device is not detected.

Doing a cat /proc/bus/usb/devices shows that the device IS plugged in and detected but no device driver is associated with it:

shen@localhost ~ $ cat /proc/bus/usb/devices

[snip]

T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 3 Spd=480 MxCh= 0

D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1

P: Vendor=050d ProdID=7050 Rev= 0.01

S: Manufacturer=Belkin

S: Product=Belkin 54g USB Network Adapter

C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=300mA

I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Looks from DMESG as if kernel module for SMP processor is installed even though i just downloaded the generic driverloader-2.28.tar.gz files from https://www.linuxant.com/driverloader/wlan/full/downloads.php and did a make install (which seemed to work fine).

Not sure what to do now. Any help would be very much appreciated.

Julian

PS - here is DMESG output in case it is helpful:

Linux version 2.6.10-gentoo-r6 (root@localhost) (gcc version
3.3.5-20050130 (Gentoo Linux 3.3.5.20050130-r1, ssp-3.3.5.20050130-1,
pie-8.7.7.1)) #7 SMP Mon Aug 15 17:38:54 BST 2005

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)

BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)

BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)

BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)

BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)

BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)

BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)

511MB LOWMEM available.

found SMP MP-table at 000f50b0

On node 0 totalpages: 131056

DMA zone: 4096 pages, LIFO batch:1

Normal zone: 126960 pages, LIFO batch:16

HighMem zone: 0 pages, LIFO batch:1

DMI 2.3 present.

ACPI: RSDP (v000
Nvidia
) @ 0x000f69f0

ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x1fff3000

ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x1fff3040

ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x1fff74c0

ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000

ACPI: Local APIC address 0xfee00000

ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)

Processor #0 6:8 APIC version 16

ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])

ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])

IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23

ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

ACPI: BIOS IRQ0 pin2 override ignored.

ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

ACPI: IRQ9 used by override.

Enabling APIC mode: Flat. Using 1 I/O APICs

Using ACPI (MADT) for SMP configuration information

Built 1 zonelists

Kernel command line: root=/dev/hda7

mapped APIC to ffffd000 (fee00000)

mapped IOAPIC to ffffc000 (fec00000)

Initializing CPU#0

CPU 0 irqstacks, hard=c0563000 soft=c055b000

PID hash table entries: 2048 (order: 11, 32768 bytes)

Detected 1797.138 MHz processor.

Using tsc for high-res timesource

Console: colour VGA+ 80x25

Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Memory: 513764k/524224k available (3028k kernel code, 9920k reserved, 1152k data, 252k init, 0k highmem)

Checking if this processor honours the WP bit even in supervisor mode... Ok.

Calibrating delay loop... 3555.32 BogoMIPS (lpj=1777664)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000

CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000

CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)

CPU: L2 Cache: 64K (64 bytes/line)

CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

CPU0: AMD Duron(tm) p stepping 01

per-CPU timeslice cutoff: 182.86 usecs.

task migration cache decay timeout: 1 msecs.

Total of 1 processors activated (3555.32 BogoMIPS).

ENABLING IO-APIC IRQs

.TIMER: vector=0x31 pin1=0 pin2=-1

Brought up 1 CPUs

CPU0:

domain 0: span 01

groups: 01

domain 1: span 01

groups: 01

NET: Registered protocol family 16

PCI: PCI BIOS revision 2.10 entry at 0xfaa50, last bus=2

PCI: Using configuration type 1

mtrr: v2.0 (20020519)

ACPI: Subsystem revision 20041105

ACPI: Interpreter enabled

ACPI: Using IOAPIC for interrupt routing

ACPI: PCI Root Bridge [PCI0] (00:00)

PCI: Probing PCI hardware (bus 00)

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]

ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)

ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)

ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)

ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)

ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)

ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.

ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.

ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.

ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.

ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.

ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.

ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.

ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.

Linux Plug and Play Support v0.97 (c) Adam Belay

pnp: PnP ACPI init

pnp: PnP ACPI: found 14 devices

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

PCI: Using ACPI for IRQ routing

** PCI interrupts are no longer routed automatically. If this

** causes a device to stop working, it is probably because the

** driver failed to call pci_enable_device(). As a temporary

** workaround, the "pci=routeirq" argument restores the old

** behavior. If this argument makes the device work again,

** please email the output of "lspci" to [email protected]

** so I can fix the driver.

pnp: 00:00: ioport range 0x1000-0x107f could not be reserved

pnp: 00:00: ioport range 0x1080-0x10ff has been reserved

pnp: 00:00: ioport range 0x1400-0x147f has been reserved

pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved

pnp: 00:00: ioport range 0x1800-0x187f has been reserved

pnp: 00:00: ioport range 0x1880-0x18ff has been reserved

pnp: 00:01: ioport range 0x1c00-0x1c3f has been reserved

pnp: 00:01: ioport range 0x2000-0x203f has been reserved

Machine check exception polling timer started.

audit: initializing netlink socket (disabled)

audit(1126787238.228:0): initialized

devfs: 2004-01-31 Richard Gooch ([email protected])

devfs: boot_options: 0x1

NTFS driver 2.1.22 [Flags: R/W DEBUG].

inotify device minor=63

lp: driver loaded but no devices found

Non-volatile memory driver v1.2

Linux agpgart interface v0.100 (c) Dave Jones

vesafb: NVIDIA Corporation, NV34 Board - p162-1n , Chip Rev (OEM: NVIDIA)

vesafb: VBE version: 3.0

vesafb: protected mode interface info at c000:dec0

vesafb: pmi: set display start = c00cdef6, set palette = c00cdf60

vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da

vesafb: hardware supports DCC2 transfers

vesafb: monitor limits: vf = 160 Hz, hf = 70 kHz, clk = 120 MHz

vesafb: scrolling: redraw

Console: switching to colour frame buffer device 80x30

vesafb: framebuffer at 0xe0000000, mapped to 0xe0880000, using 600k, total 131072k

fb0: VESA VGA frame buffer device

ACPI: Power Button (FF) [PWRF]

serio: i8042 AUX port at 0x60,0x64 irq 12

serio: i8042 KBD port at 0x60,0x64 irq 1

Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled

ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

mice: PS/2 mouse device common for all mice

input: AT Translated Set 2 keyboard on isa0060/serio0

input: PS/2 Generic Mouse on isa0060/serio1

parport: PnPBIOS parport detected.

parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]

lp0: using parport0 (interrupt-driven).

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

elevator: using anticipatory as default io scheduler

Floppy drive(s): fd0 is 1.44M

FDC 0 is a post-1991 82077

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

8139too Fast Ethernet driver 0.9.27

ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16

ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 16 (level, high) -> IRQ 16

eth0: RealTek RTL8139 at 0xc000, 00:0d:61:44:a8:02, IRQ 16

eth0: Identified 8139 chip type 'RTL-8100B/8139D'

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

NFORCE2: IDE controller at PCI slot 0000:00:09.0

NFORCE2: chipset revision 162

NFORCE2: not 100% native mode: will probe irqs later

NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.

NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller

ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA

Probing IDE interface ide0...

hda: Maxtor 6Y160P0, ATA DISK drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

Probing IDE interface ide1...

hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive

ide1 at 0x170-0x177,0x376 on irq 15

Probing IDE interface ide2...

ide2: Wait for ready failed before probe !

Probing IDE interface ide3...

ide3: Wait for ready failed before probe !

Probing IDE interface ide4...

ide4: Wait for ready failed before probe !

Probing IDE interface ide5...

ide5: Wait for ready failed before probe !

hda: max request size: 1024KiB

hda: 312581808 sectors (160041 MB) w/7936KiB Cache, CHS=19457/255/63, UDMA(100)

hda: cache flushes supported

/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 >

hdd: ATAPI 48X DVD-ROM drive, 512kB Cache

Uniform CD-ROM driver Revision: 3.20

libata version 1.10 loaded.

ieee1394: raw1394: /dev/raw1394 device initialized

ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22

ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 22 (level, high) -> IRQ 22

ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller

PCI: Setting latency timer of device 0000:00:02.2 to 64

ehci_hcd 0000:00:02.2: irq 22, pci mem 0xef000000

ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1

PCI: cache line size of 64 is not supported by device 0000:00:02.2

ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 6 ports detected

ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)

ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21

ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 21 (level, high) -> IRQ 21

ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller

PCI: Setting latency timer of device 0000:00:02.0 to 64

ohci_hcd 0000:00:02.0: irq 21, pci mem 0xef004000

ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 3 ports detected

ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20

ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 20 (level, high) -> IRQ 20

ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)

PCI: Setting latency timer of device 0000:00:02.1 to 64

ohci_hcd 0000:00:02.1: irq 20, pci mem 0xef005000

ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 3 ports detected

USB Universal Host Controller Interface driver v2.2

usb 1-6: new high speed USB device using ehci_hcd and address 3

usbcore: registered new driver usblp

drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

usb 3-1: new low speed USB device using ohci_hcd and address 2

input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:02.1-1

usbcore: registered new driver usbhid

drivers/usb/input/hid-core.c: v2.0:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 15 07:17:53 2004 UTC).

ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22

ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 22 (level, high) -> IRQ 22

PCI: Setting latency timer of device 0000:00:06.0 to 64

intel8x0_measure_ac97_clock: measured 49823 usecs

intel8x0: clocking to 47356

ALSA device list:

#0: NVidia nForce2 with ALC655 at 0xef002000, irq 22

oprofile: using NMI interrupt.

NET: Registered protocol family 2

IP: routing cache hash table of 4096 buckets, 32Kbytes

TCP: Hash tables configured (established 32768 bind 32768)

ip_conntrack version 2.1 (4095 buckets, 32760 max) - 304 bytes per conntrack

ip_tables: (C) 2000-2002 Netfilter core team

ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/

arp_tables: (C) 2002 David S. Miller

NET: Registered protocol family 1

NET: Registered protocol family 17

ACPI wakeup devices:

HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1

ACPI: (supports S0 S1 S4 S5)

ReiserFS: hda7: found reiserfs format "3.6" with standard journal

ReiserFS: hda7: using ordered data mode

ReiserFS: hda7: journal params: device hda7, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30

ReiserFS: hda7: checking transaction log (hda7)

ReiserFS: hda7: Using r5 hash to sort names

VFS: Mounted root (reiserfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 252k freed

Adding 497972k swap on /dev/hda5. Priority:-1 extents:1

device-mapper: 4.3.0-ioctl (2004-09-30) initialised: [email protected]

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

ReiserFS: dm-3: found reiserfs format "3.6" with standard journal

ReiserFS: dm-3: using ordered data mode

ReiserFS: dm-3: journal params: device dm-3, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30

ReiserFS: dm-3: checking transaction log (dm-3)

ReiserFS: dm-3: Using r5 hash to sort names

ReiserFS: dm-2: found reiserfs format "3.6" with standard journal

ReiserFS: dm-2: using ordered data mode

ReiserFS: dm-2: journal params: device dm-2, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30

ReiserFS: dm-2: checking transaction log (dm-2)

ReiserFS: dm-2: Using r5 hash to sort names

ReiserFS: dm-0: found reiserfs format "3.6" with standard journal

ReiserFS: dm-0: using ordered data mode

ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30

ReiserFS: dm-0: checking transaction log (dm-0)

ReiserFS: dm-0: Using r5 hash to sort names

ReiserFS: dm-1: found reiserfs format "3.6" with standard journal

ReiserFS: dm-1: using ordered data mode

ReiserFS: dm-1: journal params: device dm-1, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30

ReiserFS: dm-1: checking transaction log (dm-1)

ReiserFS: dm-1: Using r5 hash to sort names

ReiserFS: dm-4: found reiserfs format "3.6" with standard journal

ReiserFS: dm-4: using ordered data mode

ReiserFS: dm-4: journal params: device dm-4, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30

ReiserFS: dm-4: checking transaction log (dm-4)

ReiserFS: dm-4: Using r5 hash to sort names

driverloader: version magic '2.6.10-gentoo-r6 SMP preempt K7 gcc-3.3'
should be '2.6.10-gentoo-r6 SMP preempt K7 4KSTACKS gcc-3.3'

eth0: link down

fbsplash: console 0 using theme 'default'

fbsplash: console 1 using theme 'default'

fbsplash: console 2 using theme 'default'

fbsplash: console 3 using theme 'default'

fbsplash: console 4 using theme 'default'

fbsplash: console 5 using theme 'default'

fbsplash: console 6 using theme 'default'

fbsplash: console 7 using theme 'default'

fbsplash: console 8 using theme 'default'

fbsplash: console 9 using theme 'default'

fbsplash: console 10 using theme 'default'

driverloader: version magic '2.6.10-gentoo-r6 SMP preempt K7 gcc-3.3'
should be '2.6.10-gentoo-r6 SMP preempt K7 4KSTACKS gcc-3.3'

driverloader: version magic '2.6.10-gentoo-r6 SMP preempt K7 gcc-3.3'
should be '2.6.10-gentoo-r6 SMP preempt K7 4KSTACKS gcc-3.3'

Lycos email has now 300 Megabytes of free storage... Get it now at mail.lycos.co.uk

_______________________________________________
driverloader mailing list
[email protected]
https://www.linuxant.com/mailman/listinfo/driverloader