Re: Allnet 0281 WPA config

Hi,

it seems that the installed Windows XP driver only support WPA "One" and 
not WPA 2. If your access point is configured to only use WPA 2, it is 
then normal that it is not detected by wpa_supplicant. If this is the 
case, please try to configure your access point to use WPA "One" and not 
WPA 2.

You could also test your WPA setup with another machine and/or OS just 
to make sure it's working fine. You could also try to use DriverLoader 
with WPA to see if this is a WPA specific problem or not.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
[email protected]



Joerg Bingemer wrote:
> Hi,
> 
> I just downloaded the trial version of the driver loader. I installed 
> the trial and added the driver for the card over the web setup.
> 
> This looks for me like everything went well:
> 
> driverloader: stack=8192/60/0
> usbcore: registered new driver driverloader
> driverloader: alnetg.sys: 0xd0d4a000..0xd0d9e200 entry = d0d70130 (pbase 
> = 0x10000)
> ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 21 (level, low) -> IRQ 209
> eth1: New link status: Disconnected (0002)
> eth1: WPA, AES, TKIP, WEP128, WEP64 supported
> eth1: at 0000:03:09.0 (MAC address 00:0F:A3:1B:14:33) ready
> 
> Has someone good tipps with examples ? Here is my wpa_supplicant output:
> 
> wpa_supplicant -i eth1 -c /etc/wpa_supplicant.conf -dd
> Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 
> 'default'
> Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
> Reading configuration file '/etc/wpa_supplicant.conf'
> ctrl_interface='/var/run/wpa_supplicant'
> ctrl_interface_group=0
> eapol_version=1
> ap_scan=1
> fast_reauth=1
> Line: 264 - start of a new network block
> ssid - hexdump_ascii(len=23):
>     46 52 49 54 5a 21 42 6f 78 20 46 6f 6e 20 57 4c   FRITZ!Box Fon WL
>     41 4e 20 37 31 37 30                              AN 7170
> proto: 0x2
> key_mgmt: 0x2
> pairwise: 0x10
> group: 0x10
> PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]
> priority=5 (0x5)
> PSK (from passphrase) - hexdump(len=32): [REMOVED]
> Priority group 5
>   id=0 ssid='FRITZ!Box Fon WLAN 7170'
> Initializing interface (2) 'eth1'
> EAPOL: SUPP_PAE entering state DISCONNECTED
> EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> EAPOL: SUPP_BE entering state INITIALIZE
> EAP: EAP entering state DISABLED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> Own MAC address: 00:0f:a3:1b:14:33
> wpa_driver_hostap_set_wpa: enabled=1
> wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
> wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
> wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
> wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
> wpa_driver_hostap_set_countermeasures: enabled=0
> wpa_driver_hostap_set_drop_unencrypted: enabled=1
> Setting scan request: 0 sec 100000 usec
> RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
> RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
> Starting AP scan (broadcast SSID)
> EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
> EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
> EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
> Wireless event: cmd=0x8b19 len=8
> Received 273 bytes of scan results (1 BSSes)
> Scan results: 1
> Selecting BSS from priority group 5
> 0: 00:15:0c:cd:59:8a ssid='' wpa_ie_len=0 rsn_ie_len=0
>   skip - no WPA/RSN IE
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
> Signal 2 received - terminating
> 
> I want to connect to a FritzBox 7170 Wlan (I don't know which WPA 
> Version is used, I think WPA2)
> 
> Best Regards
> Joerg
> _______________________________________________
> driverloader mailing list
> [email protected]
> https://www.linuxant.com/mailman/listinfo/driverloader