RE: [leaf-wisp] Wireless
"Andy Henckel" <[email protected]>
| Newsgroups | gmane.linux.leaf.wisp-dist |
|---|---|
| Message-ID | <40C1034EE7C07D4587AE1F665D1B7E88DD0957@gallatin.UPSTREAM.CUTTHROATCOM.COM> |
Hmm.. not quite sure how to access /proc/interrupts.. I am really a linux newb.
Here I am sending the system log. Again, if you have a moment, the device is accessible at 64.25.142.172 via SSH. no pwd.
I will try after sending this message to put the pcmcia card into another motherboard slot.
I also changed the configuration to refelct Bridging instead of nat.. because of the problem that was described in the last post.
Thanks,
Andy
syslogd 1.3-3#31.slink1: restart. x
x kernel: klogd 1.3-3#31.slink1, log source = /proc/kmsg started. x
x kernel: Cannot find map file. x
x kernel: Loaded 239 symbols from 40 modules. x
x kernel: Linux version 2.4.20 ([email protected]***********) (gcc version 2. x
x kernel: BIOS-provided physical RAM map: x
x kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) x
x kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) x
x kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) x
x kernel: BIOS-e820: 0000000000100000 - 0000000003ffd000 (usable) x
x kernel: BIOS-e820: 0000000003ffd000 - 0000000003fff000 (ACPI data) x
x kernel: BIOS-e820: 0000000003fff000 - 0000000004000000 (ACPI NVS) x
x kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) x
x kernel: 63MB LOWMEM available. x
x kernel: On node 0 totalpages: 16381 x
x kernel: zone(0): 4096 pages.
kernel: zone(1): 12285 pages. x
x kernel: zone(2): 0 pages. x
x kernel: Kernel command line: BOOT_IMAGE=linux rw initrd=initrd.lrp init= x
x kernel: Initializing CPU#0 x
x kernel: Detected 350.799 MHz processor. x
x kernel: Console: colour VGA+ 80x25 x
x kernel: Calibrating delay loop... 699.59 BogoMIPS x
x kernel: Memory: 62676k/65524k available (959k kernel code, 2460k reserve x
x kernel: Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) x
x kernel: Inode cache hash table entries: 4096 (order: 3, 32768 bytes) x
x kernel: Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) x
x kernel: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) x
x kernel: Page-cache hash table entries: 16384 (order: 4, 65536 bytes) x
x kernel: CPU: L1 I cache: 16K, L1 D cache: 16K x
x kernel: Intel machine check architecture supported. x
x kernel: Intel machine check reporting enabled on CPU#0.
kernel: CPU: After generic, caps: 0183f9ff 00000000 00000000 0000000 x
x kernel: CPU: Common caps: 0183f9ff 00000000 00000000 0000000 x
x kernel: CPU: Intel Celeron (Covington) stepping 02 x
x kernel: Enabling fast FPU save and restore... done. x
x kernel: Checking 'hlt' instruction... OK. x
x kernel: POSIX conformance testing by UNIFIX x
x kernel: PCI: PCI BIOS revision 2.10 entry at 0xf0720, last bus=1 x
x kernel: PCI: Using configuration type 1 x
x kernel: PCI: Probing PCI hardware x
x kernel: PCI: Using IRQ router PIIX [8086/7110] at 00:04.0 x
x kernel: PCI: Found IRQ 3 for device 00:04.2 x
x kernel: PCI: Sharing IRQ 3 with 00:09.0 x
x SA-WISPDIST2426 cardmgr[1917]: + insmod: /lib/modules/2.4.20: No such fi x
x kernel: hostap_cs: hostap_cs.c 0.0.0 2002-05-16 (SSH Communications Secu x
x kernel: hostap_cs: (c) SSH Communications Security Corp <jkm@*****> x
x cardmgr[1917]: + Using /modules/preferred/pcmcia/hostap_cs.o
kernel: hostap_cs: setting Vcc=33 (constant) x
x kernel: hostap_cs: CS_EVENT_CARD_INSERTION x
x kernel: prism2_config() x
x kernel: hostap_cs: setting Vcc=50 (from config) x
x kernel: CISTPL_MANFID: 0xd601, 0x0005 x
x kernel: Checking CFTABLE_ENTRY 0x01 (default 0x01) x
x kernel: IO window settings: cfg->io.nwin=1 dflt.io.nwin=1 x
x kernel: io->flags = 0x0046, io.base=0x0000, len=64 x
x kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x290-0x2 x
x kernel: cs: IO port probe 0x0178-0x028f: clean. x
x kernel: cs: IO port probe 0x0298-0x036f: clean. x
x kernel: cs: IO port probe 0x0378-0x03bf: clean. x
x kernel: cs: IO port probe 0x03e0-0x04cf: clean. x
x kernel: cs: IO port probe 0x04d8-0x04ff: clean. x
x kernel: cs: IO port probe 0x0800-0x08ff: clean. x
x kernel: cs: IO port probe 0x0a00-0x0aff: clean.
kernel: cs: IO port probe 0x0c00-0x0cff: clean. x
x kernel: hostap_cs: index 0x01: Vcc 5.0, irq 5, io 0x0100-0x013f x
x kernel: hostap_cs: Registered netdevice netcs0 x
x kernel: prism2_hw_init() x
x kernel: prism2_hw_config: initialized in 16822 iterations x
x kernel: netcs0: NIC: id=0x800c v1.0.0 x
x kernel: netcs0: PRI: id=0x15 v1.1.1 x
x kernel: netcs0: STA: id=0x1f v1.7.4 x
x cardmgr[1917]: executing: './network start netcs0 0' x
x cardmgr[1917]: + iwconfig netcs0 mode MASTER x
x cardmgr[1917]: + iwconfig netcs0 channel 1 x
x cardmgr[1917]: + iwconfig netcs0 key OFF x
x cardmgr[1917]: + iwconfig netcs0 essid "ZCASA-DIST" x
x cardmgr[1917]: + iwconfig netcs0 nick "ZCASA-WISPDIST" x
x cardmgr[1917]: + iwpriv netcs0 maccmd 0 x
x cardmgr[1917]: + iwpriv netcs0 maccmd 4
kernel: netcs0: Deauthenticate all stations x
x root: ifup: Bringing up interface netcs0 x
x kernel: netcs0: prism2_open x
x /usr/sbin/cron[1997]: (CRON) INFO (pidfile fd = 3) x
x /usr/sbin/cron[1998]: (CRON) STARTUP (fork ok) x
x /sbin/getty[2019]: ttyS0: ioctl: Input/output error x
x sshd[2011]: Server listening on 0.0.0.0 port 22. x
x login[2016]: root login on `tty1' x
x /sbin/getty[2031]: ttyS0: ioctl: Input/output error x
x /sbin/getty[2043]: ttyS0: ioctl: Input/output error x
x /USR/SBIN/CRON[2045]: (root) CMD (/usr/sbin/checkping) x
x /sbin/getty[2048]: ttyS0: ioctl: Input/output error x
x /sbin/getty[2052]: ttyS0: ioctl: Input/output error x
x /sbin/getty[2054]: ttyS0: ioctl: Input/output error x
x /sbin/getty[2056]: ttyS0: ioctl: Input/output error x
x /sbin/getty[2057]: ttyS0: ioctl: Input/output error
/sbin/getty[2059]: ttyS0: ioctl: Input/output error x
x /sbin/getty[2061]: ttyS0: ioctl: Input/output error x
x init: Id "T1" respawning too fast: disabled for 5 minutes x
x /USR/SBIN/CRON[2066]: (root) CMD (/usr/sbin/checkping) x
x sshd[2069]: Accepted without authentication for root from 64.25.142.170 x
x sshd[2070]: Could not reverse map address 64.25.142.170.
________________________________
From: Vladimir Ivaschenko [mailto:[email protected]]
Sent: Tue 5/18/2004 9:11 AM
To: Andy Henckel; [email protected]
Subject: Re: [leaf-wisp] Wireless
I don't think it is the card. Most probably there is interrupt problem
with your Ricoh.
Please send me output of /proc/interrupts
Andy Henckel wrote:
> Indeed... I have build Karlnet Flashrom units before, and I used the parts from one I hadn't put together.
>
> So I think it is a Richo based one.
> It finds the card just fine.. but doesn't bring up the AP properly.
> I am using the partition based installation 2426.
> I tried one from your site.. 1.3.1p26 but it seems to have some differences. 1.3.1p26 would tell me a TX error all the time.
> /start
> root: ifup: Bringing up interface netcs0 x
> x cardmgr[2000]: socket 0: Zcomax XI-325H 200mW x
> x cardmgr[2000]: executing: 'modprobe hostap_crypt' x
> x cardmgr[2000]: + insmod: /lib/modules/2.4.20: No such file or directory x
> x kernel: hostap_crypt: registered algorithm 'NULL' x
> x cardmgr[2000]: + Using /modules/hostap_crypt.o x
> x cardmgr[2000]: executing: 'modprobe hostap_crypt_wep' x
> x cardmgr[2000]: + insmod: /lib/modules/2.4.20: No such file or directory x
> x kernel: hostap_crypt: registered algorithm 'WEP' x
> x cardmgr[2000]: + Using /modules/hostap_crypt_wep.o x
> x cardmgr[2000]: executing: 'modprobe hostap' x
> x cardmgr[2000]: + insmod: /lib/modules/2.4.20: No such file or directory x
> x cardmgr[2000]: + Using /modules/hostap.o x
> x cardmgr[2000]: executing: 'modprobe hostap_cs' x
> x cardmgr[2000]: + insmod: /lib/modules/2.4.20: No such file or directory
> kernel: hostap_cs: hostap_cs.c 0.0.0 2002-05-16 (SSH Communications Secu x
> x kernel: hostap_cs: (c) SSH Communications Security Corp <[email protected]> x
> x cardmgr[2000]: + Using /modules/preferred/pcmcia/hostap_cs.o x
> x kernel: hostap_cs: setting Vcc=33 (constant) x
> x kernel: hostap_cs: CS_EVENT_CARD_INSERTION x
> x kernel: prism2_config() x
> x kernel: hostap_cs: setting Vcc=50 (from config) x
> x kernel: CISTPL_MANFID: 0xd601, 0x0005 x
> x kernel: Checking CFTABLE_ENTRY 0x01 (default 0x01) x
> x kernel: IO window settings: cfg->io.nwin=1 dflt.io.nwin=1 x
> x kernel: io->flags = 0x0046, io.base=0x0000, len=64 x
> x kernel: hostap_cs: index 0x01: Vcc 5.0, irq 7, io 0x0100-0x013f x
> x kernel: hostap_cs: Registered netdevice netcs0 x
> x kernel: prism2_hw_init() x
> x kernel: prism2_hw_config: initialized in 17306 iterations x
> x kernel: netcs0: NIC: id=0x800c v1.0.0
> kernel: netcs0: PRI: id=0x15 v1.1.1 x
> x kernel: netcs0: STA: id=0x1f v1.5.6 x
> x cardmgr[2000]: executing: './network start netcs0 0' x
> x cardmgr[2000]: + iwconfig netcs0 mode MASTER x
> x cardmgr[2000]: + iwconfig netcs0 channel 1 x
> x cardmgr[2000]: + [: auto: unexpected operator x
> x cardmgr[2000]: + iwconfig netcs0 key OFF x
> x cardmgr[2000]: + iwconfig netcs0 essid "ZCASA-DIST" x
> x cardmgr[2000]: + iwconfig netcs0 nick "ZCASA-WISPDIST" x
> x cardmgr[2000]: + iwpriv netcs0 maccmd 0 x
> x cardmgr[2000]: + iwpriv netcs0 maccmd 4 x
> x kernel: netcs0: Deauthenticate all stations x
> x root: ifup: Bringing up interface netcs0 x
> x kernel: netcs0: prism2_open
>
>
> Then after a little while it does this..
>
> kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: CNFWEPFLAGS reading failed x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110) x
> x kernel: hfa384x_cmd: timeout on waiting pending TX x
> x kernel: netcs0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110)
>
> What do you think?
>
> You could access the unit if you like... 64.25.142.172
> root
>
> I'll try swaping cards again. I have tried all 3 different firmware revisions for the card.
>
> Thanks so much,
>
> Andy
> ________________________________
>
> From: Vladimir Ivaschenko [mailto:[email protected]]
> Sent: Tue 5/18/2004 3:18 AM
> To: Andy Henckel
> Cc: [email protected]
> Subject: Re: [leaf-wisp] Wireless
>
>
>
> I use WISP-Dist myself with Demarctech cards and they used to work fine.
>
> You use somekind of PCMCIA-PCI adapter?
>
> Andy Henckel wrote:
>
>>Hello,
>>
>>I setup wispdist on a pII350 that I had laying around the basement this weekend.
>>After grinding away for some time, I finally got everything into place... or at least the illusion thereof.
>>
>>My problem is this: I have Demarctech card. And it won't work.
>>I tried orinoco card.. but AP mode is unsupported?
>>
>>After reading the wireless thread on the list archive, I upgraded the 1.4.9 station firmware to 1.5.6
>>(primary 1.0.1 to 1.1.1)
>>
>>And it still won't work. I will try to upgrade to 1.7.4 or downgrade back to 1.5.6 with primary of 1.0.1.
>>
>>Any suggestions?
>>
>>What happens is very strange. I reboot the dist, and then with my laptop, I can see the network when I scan for AP's. As soon as I try to connect to the AP, I cannot. And then it disappears alltogether, until another reboot.
>>Although it's not like the dist is locking up or anything.
>>
>>Thanks in advance.
>>
>>Andy Henckel
>>Transaria
>>Missoula, MT.
>>
>>
>>
>>-------------------------------------------------------
>>This SF.Net email is sponsored by: SourceForge.net Broadband
>>Sign-up now for SourceForge Broadband and get the fastest
>>6.0/768 connection for only $19.95/mo for the first 3 months!
>>http://ads.osdn.com/?ad_id%62&alloc_ida84&op=click
>>_______________________________________________
>>leaf-wisp-dist mailing list
>>[email protected]
>>https://lists.sourceforge.net/lists/listinfo/leaf-wisp-dist
>>
>
>
>
> --
> Best Regards,
> Vladimir Ivashchenko
> ThunderWorx - www.thunderworx.com
> Senior Systems Designer/Engineer
>
>
>
>
--
Best Regards,
Vladimir Ivashchenko
ThunderWorx - www.thunderworx.com
Senior Systems Designer/Engineer
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g.
Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id149&alloc_id66&op=click