Re: FW: [leaf-wisp] Wireless
Vladimir Ivaschenko <[email protected]>
| Newsgroups | gmane.linux.leaf.wisp-dist |
|---|---|
| Message-ID | <[email protected]> |
There is an old image for Karlnet. You can find it at http://www.hazard.maks.net/wisp-dist/downloads/knet/ As for your problem with PCMCIA-PCI IRQ routing, did you try PCIC_OPTS options I wrote? Andy Henckel wrote: > I still have not been able to get this to work with the Demarc card. Using an ASUS pII350 board. > Tried all the different settings in for the PCMCIA cardbus. > Any other suggestions? > What's the word on Karlnet support for this device? > I have a license and the driver if you want for the TC client. > I would love if you developed that! > -----Original Message----- > From: [email protected] [mailto:[email protected]] On Behalf Of Andy Henckel > Sent: Tuesday, May 25, 2004 1:48 PM > To: Vladimir Ivaschenko; [email protected] > Subject: RE: [leaf-wisp] Wireless > > ZCASA-WISPDIST2426: -root- > # cat /proc/pci > PCI devices found: > Bus 0, device 0, function 0: > Class 0600: PCI device 8086:7190 (rev 2). > Master Capable. Latencyd. > Prefetchable 32 bit memory at 0xe4000000 [0xe7ffffff]. > Bus 0, device 1, function 0: > Class 0604: PCI device 8086:7191 (rev 2). > Master Capable. Latencyd. Min Gnt6. > Bus 0, device 4, function 0: > Class 0601: PCI device 8086:7110 (rev 2). > Bus 0, device 4, function 1: > Class 0101: PCI device 8086:7111 (rev 1). > Master Capable. Latency2. > I/O at 0xb800 [0xb80f]. > Bus 0, device 4, function 2: > Class 0c03: PCI device 8086:7112 (rev 1). > IRQ 3. > Master Capable. Latency2. > I/O at 0xb400 [0xb41f]. > Bus 0, device 4, function 3: > Class 0680: PCI device 8086:7113 (rev 2). > IRQ 9. > Bus 0, device 9, function 0: > Class 0200: PCI device 10b7:9055 (rev 48). > IRQ 3. > Master Capable. Latency2. Min Gnt.Max Lat. > I/O at 0xb000 [0xb07f]. > Non-prefetchable 32 bit memory at 0xde800000 [0xde80007f]. > Bus 0, device 10, function 0: > Class 0607: PCI device 1180:0475 (rev 128). > IRQ 4. > Master Capable. Latency2. Min Gnt8.Max Lat=7. > Non-prefetchable 32 bit memory at 0x10000000 [0x10000fff]. > Bus 0, device 11, function 0: > Class 0200: PCI device 10ec:8139 (rev 16). > IRQ 10. > Master Capable. Latency2. Min Gnt2.Max Latd. > I/O at 0xa800 [0xa8ff]. > Non-prefetchable 32 bit memory at 0xde000000 [0xde0000ff]. > Bus 0, device 12, function 0: > Class 0401: PCI device 1274:5000 (rev 0). > IRQ 11. > Master Capable. Latency2. Min Gnt.Max Lat8. > I/O at 0xa400 [0xa43f]. > Bus 1, device 0, function 0: > Class 0300: PCI device 1002:5246 (rev 0). > IRQ 11. > Master Capable. Latencyd. Min Gnt=8. > Prefetchable 32 bit memory at 0xe0000000 [0xe3ffffff]. > I/O at 0xd800 [0xd8ff]. > Non-prefetchable 32 bit memory at 0xdf000000 [0xdf003fff]. > ZCASA-WISPDIST2426: -root- > # > > As requested > > ________________________________ > > From: Vladimir Ivaschenko [mailto:[email protected]] > Sent: Tue 5/25/2004 10:55 AM > To: Andy Henckel; [email protected] > Subject: Re: [leaf-wisp] Wireless > > > > Put the following in /etc/default/pcmcia file: > PCIC_OPTS="irq_mode=0 pci_csc=0 poll_interval0" > or, if it doesn't help, > PCIC_OPTS="irq_list=0" > I would also like to have output of "cat /proc/pci" command so that I may integrate workaround for your PCMCIA bridge in future releases of WISP-Dist. > Andy Henckel wrote: > >>Search for what ? PCIC? >> >> >> -----Original Message----- >>From: Vladimir Ivaschenko [mailto:[email protected]] >>Sent: Monday, May 24, 2004 10:42 AM >>To: Andy Henckel >>Cc: [email protected] >>Subject: Re: [leaf-wisp] Wireless >> >>Ok, the controller does not pass interrupts properly. >> >>Search in the list, there was discussion about this - you need to put >>correct PCIC_OPTS parameter. >> >>Andy Henckel wrote: >> >> >>># cat /proc/interrupts >>> CPU0 >>> 0: 14857399 XT-PIC timer >>> 1: 3 XT-PIC keyboard >>> 2: 0 XT-PIC cascade >>> 4: 0 XT-PIC i82365 >>> 5: 0 XT-PIC hostap_cs >>>10: 10340 XT-PIC eth0 >>>14: 7153 XT-PIC ide0 >>>NMI: 0 >>>ERR: 0 >>> >>> >>>________________________________ >>> >>>From: Vladimir Ivaschenko [mailto:[email protected]] >>>Sent: Sun 5/23/2004 5:11 AM >>>To: Andy Henckel >>>Cc: [email protected] >>>Subject: Re: [leaf-wisp] Wireless >>> >>> >>> >>>Hi, >>> >>>You can see /proc/interrupts by issuing command "cat /proc/interrupts". >>> >>>Andy Henckel wrote: >>> >>> >>> >>>>Hmm.. not quite sure how to access /proc/interrupts.. I am really a linux newb. >>> >>> >>>-- >>>Best Regards, >>>Vladimir Ivashchenko >>>ThunderWorx - www.thunderworx.com >>>Senior Systems Designer/Engineer >>> >>> >>> >>> >> >> >> > > > -- > Best Regards, > Vladimir Ivashchenko > ThunderWorx - www.thunderworx.com > Senior Systems Designer/Engineer > > > > > > ------------------------------------------------------- > This SF.Net email is sponsored by: Oracle 10g > Get certified on the hottest thing ever to hit the market... Oracle 10g. > Take an Oracle 10g class now, and we'll give you the exam FREE. > http://ads.osdn.com/?ad_id149&alloc_id?66&op=ick > _______________________________________________ > leaf-wisp-dist mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/leaf-wisp-dist > > > > > ------------------------------------------------------- > This SF.Net email is sponsored by the new InstallShield X. >>From Windows to Linux, servers to mobile, InstallShield X is the one > installation-authoring solution that does it all. Learn more and > evaluate today! http://www.installshield.com/Dev2Dev/0504 > _______________________________________________ > leaf-wisp-dist mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/leaf-wisp-dist > -- Best Regards, Vladimir Ivashchenko ThunderWorx - www.thunderworx.com Senior Systems Designer/Engineer ------------------------------------------------------- This SF.Net email is sponsored by the new InstallShield X. From Windows to Linux, servers to mobile, InstallShield X is the one installation-authoring solution that does it all. Learn more and evaluate today! http://www.installshield.com/Dev2Dev/0504