Re: [leaf-wisp] Zebra/ospf

Hi.
Did you ever try to set OSPF neighbor manualy ?
I'm not sure if WISP Zebra pkg come with neighbor discovery.

Sincerely
-bino-
----- Original Message -----
From: "Ray Gwinn" <[email protected]>
To: "bino_oetomo" <[email protected]>
Cc: <[email protected]>
Sent: Tuesday, June 15, 2004 12:41 PM
Subject: Re: [leaf-wisp] Zebra/ospf


> I have reduced the hardware to the simplest setup.  The setup is currently
1 radio on both
> units.  The radios are both set to channel 1, and in master mode.
>
> My intent is that the 172.16.xx.xx/12 ip address are area 0.  The
10.0.0.0/24 address are
> for dhcp to assign to users.  I have tried specifically setting area 0 to
172.16.0.0/12
> instead of 0.0.0.0/0.  I read the area 0 ip of 0.0.0.0/0 to say "route
anything from
> anywhere".
>
> The "ip addr" of the node with the internet connection is first, the
remote wireless only
> node then follows.
>
> The "ospf sh run" seems to only echo the ospfd.conf file.  The ospfd.conf
file is the same
> on both nodes, and is the default shipped with wisp-disp, except for the
password and
> hostname.  The ospfd.conf follows the ip addr outputs.
>
> 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>     inet 127.0.0.1/8 scope host lo
> 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop
>     link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
> 3: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 100
>     link/ether 00:00:24:c1:b9:bc brd ff:ff:ff:ff:ff:ff
>     inet 199.250.240.253/24 scope global eth0
>     inet 172.16.6.73/12 scope global eth0
> 4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 100
>     link/ether 00:00:24:c1:b9:bd brd ff:ff:ff:ff:ff:ff
> 5: netcs0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 100
>     link/ether 00:02:6f:08:21:df brd ff:ff:ff:ff:ff:ff
>     inet 10.0.100.1/24 scope global netcs0
>     inet 172.16.6.65/12 scope global netcs0
>
>
> 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>     inet 127.0.0.1/8 scope host lo
> 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop
>     link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
> 3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 100
>     link/ether 00:00:24:c1:78:40 brd ff:ff:ff:ff:ff:ff
> 4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 100
>     link/ether 00:00:24:c1:78:41 brd ff:ff:ff:ff:ff:ff
> 5: netcs0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 100
>     link/ether 00:02:6f:08:09:6a brd ff:ff:ff:ff:ff:ff
>     inet 10.0.101.1/24 scope global netcs0
>     inet 172.16.6.81/12 scope global netcs0
>
> !
> ! Zebra configuration saved from vty
> !   2002/05/02 15:28:04
> !
> hostname win-msu-0.100.0
> password itsme$
> enable password itsme$
> log file /var/log/ospfd.log
> !
> !
> !
> interface lo
> !
> interface eth0
>  ip ospf message-digest-key 1 md5 wisp
> !
> interface eth1
>  ip ospf message-digest-key 1 md5 wisp
> !
> interface eth2
>  ip ospf message-digest-key 1 md5 wisp
> !
> interface netcs0
>  ip ospf message-digest-key 1 md5 wisp
> !
> interface netcs1
>  ip ospf message-digest-key 1 md5 wisp
> !
> interface netcs2
>  ip ospf message-digest-key 1 md5 wisp
> !
> router ospf
>  redistribute connected
>  redistribute rip
>  network 0.0.0.0/0 area 0
>  area 0 authentication message-digest
> !
> access-list vtylist permit 127.0.0.1/32
> access-list vtylist deny any
> !
> line vty
>  access-class vtylist
> !
>
>




-------------------------------------------------------
This SF.Net email is sponsored by The 2004 JavaOne(SM) Conference
Learn from the experts at JavaOne(SM), Sun's Worldwide Java Developer
Conference, June 28 - July 1 at the Moscone Center in San Francisco, CA
REGISTER AND SAVE! http://java.sun.com/javaone/sf Priority Code NWMGYKND