| Newsgroups |
gmane.linux.lfs.automated |
| Message-ID |
<[email protected]> |
15.06.2022 22:47 tarihinde Bruce Dubbs ([email protected] via
alfs-discuss Mailing List) yazdı:
> On 6/15/22 13:06, Yasin YILMAZ ([email protected] via
> alfs-discuss Mailing List) wrote:
>>
>> 15.06.2022 21:42 tarihinde Bruce Dubbs ([email protected] via
>> alfs-discuss Mailing List) yazdı:
>>> On 6/15/22 12:14, Yasin YILMAZ ([email protected] via
>>> alfs-discuss Mailing List) wrote:
>>>
>>>>
>>>> I updated it as you said, and due to the last update on git, I
>>>> pulled the files again and reconfigured them and tried it with the
>>>> updated version this time, and I still get the same error.
>>>>
>>>> ---
>>>> Building target 803-glibc
>>>> [+++++++++++make: *** [Makefile:907: 803-glibc] Error
>>>> 1 ]
>>>> 39
>>>> min. 10 sec
>>>> make[1]: *** [Makefile:113: mk_CHROOT] Error 2
>>>> make[1]: Leaving diretory '/mnt/lfs/jhalfs'
>>>
>>> Have you looked in the logs/ directory to see if there are any clues
>>> there?
>>>
>>> Have you tried to enter chroot manually and follow the book's
>>> instructions?
>
>> I'm sorry, I'm writing to you with the help of translate. Also, since
>> the /mnt/lfs/jhalfs/logs/803-glibc file is very large, I have
>> forwarded the output at the end of the file in my previous e-mail.
>> Since the problem is the same problem again, I did not throw the same
>> printouts again.
>
> OK, I went back and looked at the end of your output and compared it
> to mine. It looks like the 'make' phase completed OK. The next
> commands are:
>
> make check
> sed '/test-installation/s@$(PERL)@echo not running@' -i ../Makefile
> make install
>
> It is unclear that you disabled the checks. You can check by looking at
>
> /mnt/lfs/jhalfs/lfs-commands/chapter08/803-glibc
>
> If the checks are really disabled there should be a line:
> # make -k check >> $TEST_LOG 2>&1 || true
>
> The # is important.
>
> What I would suggest is starting over. First, make sure all the
> virtual files systems are unmounted. Use the findmnt command to
> check, Then as the root user
>
> rm -rf /mnt/lfs/{bin,dev,home,lib,mnt,proc,run,sys,usr}
> rm -rf /mnt/lfs/{boot,etc,jhalfs,lib64,media,opt,root,sbin,srv,tmp,var}
>
> Be VERY careful with the above. You do not want to remove these
> directories on the host.
>
> When you have finished, you should only have
> /mnt/lfs/{sources,lost+found}
> Now remove any sub-directories in /mnt/lfs/sources.
>
> Then remove your jhalfs git directory and
>
> git clone git clone git://git.linuxfromscratch.org/jhalfs.git
>
> Then 'cd jhalfs.git' and run 'make' paying careful attention to all
> the options.
>
> That should get you back to a clean start.
>
> -- Bruce
>
I implemented what you said. I am encountering the same error again. Is
there an alternative solution?
---
Yasin YILMAZ
--
http://lists.linuxfromscratch.org/sympa/info/alfs-discuss
Unsubscribe: See the above information page