| Newsgroups |
gmane.linux.lfs.automated |
| Message-ID |
<[email protected]> |
On Sun, 2022-12-18 at 14:14 +0100, Pierre Labastie wrote:
> On Sun, 2022-12-18 at 11:57 +0800, Patrick Star wrote:
> >
> >
> > On Sun, Dec 18, 2022 at 11:43 AM Patrick Star <[email protected]> wrote:
> > >
> > >
> > > On Sun, Dec 18, 2022 at 11:08 AM Patrick Star <[email protected]> wrote:
> > > > On Sun, Dec 18, 2022 at 12:31 AM Pierre Labastie
> > > > <[email protected]> wrote:
> > > > > On Sat, 2022-12-17 at 14:50 +0800, Patrick Star wrote:
> > > > > > Error log as below:
> > > > > > Creating Makefile... START
> > > > > > Processing... <Chapter 4>
> > > > > > sed: -e expression #1, char 17: Invalid range end
> > > > > >
> > > > > > <jhalfs> exit
> > > > > >
> > > > > > I have located it happend at jhalfs/LFS/master.sh line 69.
> > > > > >
> > > > > > 67 # Grab the name of the target
> > > > > > 68 # This is only used to check the name in "opt_override" or
> > > > > > "BLACKLIST"
> > > > > > 69 name=`echo ${this_script} | sed -e 's@[0-9]\{3,4\}-@@' \
> > > > > > 70 -e 's@-pass[0-9]\{1\}@@' \
> > > > > > 71 -e 's@-libstdc++@@' \
> > > > > > 72 -e 's,'$N',,' \
> > > > > > 73 -e 's@-32@@'`
> > > > > > 74
> > > > > >
> > > > > > But I know nothing about sed :-)
> > > > >
> > > > > This seems weird: This sed is ok for me with sed-4.9... What are your
> > > > > settings?
> > > > > Specially that of LANG (in configuration)?
> > > > >
> > > >
> > > >
> > > > LANG <en_US.UTF-8>
> > > >
> > > > Probably my sed-4.9 is broken:
> > > >
> > > > sed-4.8 is ok.
> > > > $ echo 401-creatingminlayout | sed-4.8 -e 's@[0-9]\{3,4\}-@@' -e 's@-
> > > > pass[0-9]\{1\}@@' -e s@-libstdc++@@ -e s,,, -e s@-32@@
> > > > creatingminlayout
> > > >
> > > > but not sed-4.9.
> > > > $ echo 401-creatingminlayout | sed-4.9 -e 's@[0-9]\{3,4\}-@@' -e 's@-
> > > > pass[0-9]\{1\}@@' -e s@-libstdc++@@ -e s,,, -e s@-32@@
> > > > sed-4.9: -e expression #1, char 17: Invalid range end
> > > >
> > > > Also my sed-4.9 is much smaller than sed-4.8 (both stripped).
> > > > 172K /usr/bin/sed-4.8
> > > > 108K /usr/bin/sed-4.9
> > > >
> > > >
> > >
> > >
> > > I've recompiled sed-4.9, but still has the same error.
> > > Also I found somethings interesting, both the two below commands are fine.
> > > echo 401-creatingminlayout | sed -e 's@[0-8]@@'
> > > echo 401-creatingminlayout | sed -e 's@[1-9]@@'
> > > But sed -e 's@[0-9]@@' still gave an error of "Invalid range end".
> > >
> >
> > Finally I found out it's a 'LANG' setting issue on my system, unset LANG
> > make
> > it work again.
> > $ echo 401-creatingminlayout | LANG= sed -e 's@[0-9]@@'
> >
>
> Somewhat weird: LANG=en_US.UTF-8 is pretty common... And definitely works for
> me
> with sed-4.9. What is your base distro? You could try running "localedef -i
> en_US -f UTF-8 en_US.UTF-8", and see if there is still the same issue.
Another possibility is that some LC_xxx variable is set to something weird. What
is the output of "locale"?
I can get the same message with:
---
$ echo 401-creatingminlayout |sed -e 's@[1-0]@@'
sed: -e expression #1, char 9: Invalid range end
---
So if for some reason 9 is not considered to be after 0 in the collating order,
then the message you see could be explained. Why this might have changed for you
in sed-4.9, I don't know... For me, the above command fails with the same
message when using either sed-4.8 or sed-4.9.
Pierre
--
http://lists.linuxfromscratch.org/sympa/info/alfs-discuss
Unsubscribe: See the above information page