Re: Maverick and Intel Corporation 536EP Data Fax Modem
Marvin Stodolsky <[email protected]>
| Newsgroups | gmane.linux.linmodem |
|---|---|
| Message-ID | <[email protected]> |
Scott, Unload useless slmodem driver $ sudo modprobe -r slamr Load the Intel driver $ sudo Intel537 Then again: $ sudo wvdialconf MarvS On Fri, sb 25, 2011 at 6:41 PM, Scott Cink <[email protected]> wrote: > Thanks, > > I ran wvdialconf with root permission with the same results: > > smcink@ubuntu:~/Downloads$ sudo wvdialconf > [sudo] password for smcink: > Editing `/etc/wvdial.conf'. > > Scanning your serial ports for a modem. > > ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > Modem Port Scan<*1>: S2 S3 > > > Sorry, no modem was detected! Is it in use by another program? > > > On Fri, Feb 25, 2011 at 4:32 PM, Marvin Stodolsky > <[email protected]> wrote: >> Scott >> >> RE: $ wvdialconf >> Must be done with Root permission >> $ sudo wvdialconf >> >> Also, you have installed the slmodem support, which is useless for >> your Intel537 modem >> >> MarvS >> >> On Fri, Feb 25, 2011 at 3:25 PM, Scott Cink <[email protected]> wrote: >>> Hello, I am new to Ubuntu and am trying to set up my fax modem. I >>> have installed the drivers from here: >> >>> http://groups.google.com/group/ubuntu-modems/web/intel536ep-maverick_1-Philippe.Vouters_i386.deb >>> >>> and when I run wvdialconf I get: >>> >>> smcink@ubuntu:~$ wvdialconf >>> Editing `/etc/wvdial.conf'. >>> >>> Scanning your serial ports for a modem. >>> >>> WvModem<*1>: Cannot set information for serial port. >>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>> WvModem<*1>: Cannot set information for serial port. >>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>> Modem Port Scan<*1>: S2 S3 >>> >>> >>> Sorry, no modem was detected! Is it in use by another program? >>> >>> -- >>> >>> What should I do next? >>> >> >