Re: Maverick and Intel Corporation 536EP Data Fax Modem

Scott

$ find /lib/modules -name Intel536.ko
/lib/modules/2.6.35-23-generic-pae/kernel/drivers/char/Intel536.ko
/lib/modules/2.6.35-24-generic-pae/kernel/drivers/char/Intel536.ko
/lib/modules/2.6.35-22-generic-pae/kernel/drivers/char/Intel536.ko

was displayed after running the install on my System
Though I can't test further as i can't use the pae series kernels on
my hardware.

Run the find query on your System

MarvS

On Fri, Feb 25, 2011 at 7:24 PM, Scott Cink <[email protected]> wrote:
> Seems to have trouble finding the module:
>
> smcink@ubuntu:/lib/modules/2.6.35-23-generic-pae/kernel/drivers/char$ ls
> Intel536.ko
> smcink@ubuntu:/lib/modules/2.6.35-23-generic-pae/kernel/drivers/char$
> sudo modprobe -r
> slamrsmcink@ubuntu:/lib/modules/2.6.35-23-generic-pae/kernel/drivers/char$
> sudo modprobe Intel536
> FATAL: Module Intel536 not found.
> smcink@ubuntu:/lib/modules/2.6.35-23-generic-pae/kernel/drivers/char$
> sudo modprobe Intel537
> FATAL: Module Intel537 not found.
> smcink@ubuntu:/lib/modules/2.6.35-23-generic-pae/kernel/drivers/char$
> sudo wvdialconfEditing `/etc/wvdial.conf'.
>
> Scanning your serial ports for a modem.
>
> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> Modem Port Scan<*1>: S2   S3
>
>
> Sorry, no modem was detected!  Is it in use by another program?
>
>
> On Fri, Feb 25, 2011 at 4:58 PM, Marvin Stodolsky
> <[email protected]> wrote:
>> $ sudo modprobe Intel537
>>
>> On Fri, Feb 25, 2011 at 6:58 PM, Marvin Stodolsky
>> <[email protected]> wrote:
>>> Scott,
>>>
>>> Unload  useless slmodem driver
>>> $ sudo modprobe -r slamr
>>> Load the Intel driver
>>> $ sudo Intel537
>>> Then again:
>>> $ sudo wvdialconf
>>>
>>> MarvS
>>>
>>>
>>> On Fri, sb 25, 2011 at 6:41 PM, Scott Cink <[email protected]> wrote:
>>>> Thanks,
>>>>
>>>> I ran wvdialconf with root permission with the same results:
>>>>
>>>> smcink@ubuntu:~/Downloads$ sudo wvdialconf
>>>> [sudo] password for smcink:
>>>> Editing `/etc/wvdial.conf'.
>>>>
>>>> Scanning your serial ports for a modem.
>>>>
>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>>>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>>>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>>>> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>>> Modem Port Scan<*1>: S2   S3
>>>>
>>>>
>>>> Sorry, no modem was detected!  Is it in use by another program?
>>>>
>>>>
>>>> On Fri, Feb 25, 2011 at 4:32 PM, Marvin Stodolsky
>>>> <[email protected]> wrote:
>>>>> Scott
>>>>>
>>>>> RE:  $ wvdialconf
>>>>> Must be done with Root permission
>>>>> $ sudo wvdialconf
>>>>>
>>>>> Also, you have installed the slmodem support, which is useless for
>>>>> your Intel537 modem
>>>>>
>>>>> MarvS
>>>>>
>>>>> On Fri, Feb 25, 2011 at 3:25 PM, Scott Cink <[email protected]> wrote:
>>>>>> Hello, I am new to Ubuntu and am trying to set up my fax modem.  I
>>>>>> have installed the drivers from here:
>>>>>
>>>>>> http://groups.google.com/group/ubuntu-modems/web/intel536ep-maverick_1-Philippe.Vouters_i386.deb
>>>>>>
>>>>>> and when I run wvdialconf I get:
>>>>>>
>>>>>> smcink@ubuntu:~$ wvdialconf
>>>>>> Editing `/etc/wvdial.conf'.
>>>>>>
>>>>>> Scanning your serial ports for a modem.
>>>>>>
>>>>>> WvModem<*1>: Cannot set information for serial port.
>>>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>>>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>>>>>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>>>>> WvModem<*1>: Cannot set information for serial port.
>>>>>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>>>>>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>>>>>> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>>>>> Modem Port Scan<*1>: S2   S3
>>>>>>
>>>>>>
>>>>>> Sorry, no modem was detected!  Is it in use by another program?
>>>>>>
>>>>>> --
>>>>>>
>>>>>> What should I do next?
>>>>>>
>>>>>
>>>>
>>>
>>
>