Re: Re: Re: Ludwig Gebauer, Germany, openSUSE 11.4 "Celadon" - Kernel kernel 2.6.37.1-1.2-desktop

Antonio,

yes, I did read the documentation contained in SLMODEMD_gcc4.5_alsa1.0.24.tar.gz :-))

Yes, I tried that Init2 string
Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS90
and monitored the phone line with a voltmeter and high impedance (crystal) earphones. Same result: The modem takes up the phone and hangs it up immediately, doesn't dial.

Regards
Ludwig

-------- Original-Nachricht --------
> Datum: Sun, 14 Aug 2011 12:19:31 -0500
> Von: Antonio Olivares <[email protected]>
> An: Ludwig Gebauer <[email protected]>
> CC: [email protected]
> Betreff: Re: Re: Re: Ludwig Gebauer, Germany, openSUSE 11.4 "Celadon" - Kernel kernel 2.6.37.1-1.2-desktop

> Ludwig,
> 
> Try editing your /etc/wvdial.conf file and change Init 2 as follows:
> 
> sample Init 2 line:
> 
> Modem = /dev/ttySL0
> Baud = 460800
> Init = ATZ
> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS90
> ISDN = 0
> Modem Type = Analog Modem
> Phone = YOUR_ISP_PHONE_NUMBER_GOES_HERE
> Username = YOUR_USERNAME
> Password = YOUR_PASSWORD
> Carrier Check = no
> Stupid Mode = yes
> 
> Try that and report back.
> 
> Regards,
> 
> Antonio
> 
> 
> 
> On Sun, Aug 14, 2011 at 12:08 PM, Ludwig Gebauer <[email protected]>
> wrote:
> > Marvin,
> >
> > thank you very much.
> >
> > Now the modem shows some reaction, but no real success: Wvdial exits
> with a happy "NO DIALTONE". A shot dip in phone line voltage indicates, that
> the modem picks up the phone, but immediately hangs it up again, before any
> telephone provider might have a chance to send a dialtone. The hardware
> seems o.k.; I am posting via the same hardware and phone line under SuSE 10.3.
> >
> > Fiddling with drivers (Removing oss-drivers, inserting available
> snd_intel_*-drivers) and wvdial.conf settings (Reduced baudrate, dial without
> waiting for dialtone, etc.) brought no change.
> >
> > Suspicious:
> >
> > linux-k7za:~ # slmodemd -c GERMANY --alsa hw:0,6
> > SmartLink Soft Modem: version 2.9.11 Aug  9 2011 14:15:04
> > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created.
> > modem `hw:0,6' created. TTY is `/dev/pts/2'
> > error: sched_setscheduler: Operation not permitted
> > Use `/dev/ttySL0' as modem device, Ctrl+C for termination.
> >
> > Whitch Operation?? I suspected a priority problem, invoced slmodend with
> nice -20, but no change.
> >
> > Also suspicious:
> >
> > linux-k7za:~ # dmesg
> > .
> > .
> > [  536.642852] hda-intel: IRQ timing workaround is activated for card
> #0. Suggest a bigger bdl_pos_adj.
> >
> > Regards
> > Ludwig

-- 
Empfehlen Sie GMX DSL Ihren Freunden und Bekannten und wir
belohnen Sie mit bis zu 50,- Euro! https://freundschaftswerbung.gmx.de