Re: Linux-wlan-user Digest, Vol 26, Issue 9

Try add the line "$WLANCTL $1 lnxreq_ifstate ifstate=disable" after line "# 
Enable the interface" in /etc/wlan/shared

On 9/10/05, [email protected] <
[email protected]> wrote: 
> 
> Send Linux-wlan-user mailing list submissions to
> [email protected]
> 
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.linux-wlan.com/mailman/listinfo/linux-wlan-user
> or, via email, send a message with subject or body 'help' to
> [email protected]
> 
> You can reach the person managing the list at
> [email protected]
> 
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Linux-wlan-user digest..."
> 
> 
> Today's Topics:
> 
> 1. Is the usb driver in 0.2.2 release stable enough to be used?
> (Gavin Li)
> 
> 
> 
> ---------- Forwarded message ----------
> From: Gavin Li <[email protected]>
> To: [email protected], 
> [email protected]
> Date: Thu, 8 Sep 2005 11:30:51 -0400
> Subject: [lwlan-user] Is the usb driver in 0.2.2 release stable enough to 
> be used?
> Several day ago, I had problem to use prism2_usb driver in 2.4.3x kernel,
> but it keep crash linux kernel when doing hotplug, so I gave up, and I
> decided to move to 2.6 kernel, Luckly, it doesn't crash my new-installed
> RHFC 3 system, but when do hotplug, I always get these message.
> 
> [root@localhost init.d]# hfa384x_usbctlx_complete_sync: CTLX[5] error:
> state(Request failed)
> hfa384x_drvr_readpda: Read from index 0 failed, continuing
> hfa384x_usbctlx_complete_sync: CTLX[5] error: state(Request failed)
> hfa384x_drvr_readpda: Read from index 1 failed, continuing
> hfa384x_drvr_readpda: pdrlen invalid=1026
> prism2mgmt_readpda: hfa384x_drvr_readpda() failed, result=-61
> hfa384x_usbctlx_complete_sync: CTLX[4] error: state(Request failed)
> hfa384x_usbctlx_complete_sync: CTLX[4] error: state(Request failed)
> hfa384x_usbctlx_complete_sync: CTLX[4] error: state(Request failed)
> hfa384x_usbctlx_complete_sync: CTLX[1] error: state(Request failed)
> hfa384x_usbctlx_complete_sync: CTLX[5] error: state(Request failed)
> hfa384x_drvr_readpda: Read from index 0 failed, continuing
> hfa384x_usbctlx_complete_sync: CTLX[5] error: state(Request failed)
> hfa384x_drvr_readpda: Read from index 1 failed, continuing
> hfa384x_usbctlx_complete_sync: CTLX[5] error: state(Request failed)
> hfa384x_drvr_readpda: Read from index 2 failed, continuing
> prism2mgmt_readpda: hfa384x_drvr_readpda() failed, result=-61
> 
> 
> The sequence I did is:
> bootup RHFC3,
> plug in USB wireless card, and found p80211.o & prism2_usb.o are loaded
> /etc/init.d/wlan start
> /sbin/ifconfig wlan0 10.0.39.1 <http://10.0.39.1>
> ping 10.0.39.241 <http://10.0.39.241>
> everything OK
> unplug USB card
> wait several seconds
> plug in USB card
> 
> If I do " ifconfig wlan0 down && /etc/init.d/wlan stop" before I unplug 
> USB
> card, I will see the two modules are removed, and when I plug in it back, 
> I
> have this:
> [root@localhost init.d]# prism2usb_init: prism2_usb.o: 0.2.2 Loaded
> prism2usb_init: dev_info is: prism2_usb
> < following withe all the error message from above >
> 
> 
> 
> _______________________________________________
> Linux-wlan-user mailing list
> [email protected]
> http://lists.linux-wlan.com/mailman/listinfo/linux-wlan-user
> 
> 
>

_______________________________________________
Linux-wlan-user mailing list
[email protected]
http://lists.linux-wlan.com/mailman/listinfo/linux-wlan-user