Re: (resend) may bug: lvconvert reports "Insufficient free space" when doing "--replace"

Hemng,

'lvconvert --replace ..." reports the new PV does  not have enough space
(89 needed/49 available) to suit full replacement and rejects as
replacement requires complete SubLVs to move off respective PVs.

Check lsblk (or lvs -ao+devices) after the pvmove to confirm a partial move
across resulting remaining allocations for leg 0 on /dev/sdh, i.e no
replacement

Use a larger PV to be able to replace.

Best,
Heinz

On Mon, Nov 8, 2021 at 7:46 AM [email protected] <[email protected]>
wrote:

> (I sent this mail some days before, it looks this mail was blocked by
> anti-spam system. resend it)
>
> Hello list,
>
> I may found a bug, when lv is raid1, and each leg includes more than one
> PV.
>
> When doing "lvconvert --replace" to replace one of the oldpv with a newpv,
> It looks lvconvert requires full raid array size for a single newpv.
>
> lvm version: 2.03.12, Reproducible steps:
>
> ```
> # vgcreate vg1 /dev/sdg /dev/sdh
>    Volume group "vg1" successfully created
>
> # lvcreate -n lv1 -l 90%FREE vg1
>    Logical volume "lv1" created.
>
> # vgextend vg1 /dev/sdj /dev/sdk
>    Physical volume "/dev/sdj" successfully created.
>    Physical volume "/dev/sdk" successfully created.
>    Volume group "vg1" successfully extended
>
> # lvconvert --type raid1 vg1/lv1 /dev/sdg /dev/sdh /dev/sdj /dev/sdk
> Are you sure you want to convert linear LV vg1/lv1 to raid1 type? [y/n]: y
>    Logical volume vg1/lv1 successfully converted.
>
> # lsblk
> NAME               MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
> sdg                  8:96   0  200M  0 disk
> └─vg1-lv1_rimage_0 254:4    0  352M  0 lvm
>    └─vg1-lv1        254:2    0  352M  0 lvm
> sdh                  8:112  0  200M  0 disk
> ├─vg1-lv1_rmeta_0  254:3    0    4M  0 lvm
> │ └─vg1-lv1        254:2    0  352M  0 lvm
> └─vg1-lv1_rimage_0 254:4    0  352M  0 lvm
>    └─vg1-lv1        254:2    0  352M  0 lvm
> sdi                  8:128  0  200M  0 disk
> sdj                  8:144  0  200M  0 disk
> ├─vg1-lv1_rmeta_1  254:5    0    4M  0 lvm
> │ └─vg1-lv1        254:2    0  352M  0 lvm
> └─vg1-lv1_rimage_1 254:6    0  352M  0 lvm
>    └─vg1-lv1        254:2    0  352M  0 lvm
> sdk                  8:160  0  200M  0 disk
> └─vg1-lv1_rimage_1 254:6    0  352M  0 lvm
>    └─vg1-lv1        254:2    0  352M  0 lvm
> sdl                  8:176  0  200M  0 disk
>
> # vgextend vg1 /dev/sdi
>    Volume group "vg1" successfully extended
>
> # lvconvert --replace /dev/sdh vg1/lv1 /dev/sdi  (<=== failed, should
> succeed)
>    Insufficient free space: 89 extents needed, but only 49 available
>    LV vg1/lv1 in not partial.
>
> # lvconvert --replace /dev/sdg vg1/lv1 /dev/sdi   (<=== failed, should
> succeed)
>    Insufficient free space: 89 extents needed, but only 49 available
>    LV vg1/lv1 in not partial.
>
> # pvmove /dev/sdh /dev/sdi
>    /dev/sdh: Moved: 2.50%
>    /dev/sdh: Moved: 100.00%
> ```
>
> pvmove is workable, but I think it's a work around.
> lvconvert should run successfully with above cmds.
>
> Thanks,
> Heming
>
>
> _______________________________________________
> linux-lvm mailing list
> [email protected]
> https://listman.redhat.com/mailman/listinfo/linux-lvm
> read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

_______________________________________________
linux-lvm mailing list
[email protected]
https://listman.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/