Re: Re: Ruhezustand bei IBM thinkpad

Am Montag, 23. Mai 2005 04:12 schrieb Helge Hielscher:

> Bekommst du Fehlermeldungen in /var/log/messages ?
> Was bringt "service usb restart"?
> Was passiert wenn du "service usb stop" vor dem Schlafen und "service usb
> start" nach dem Aufwecken ausführst?

'May 24 15:45:05 localhost kernel: usb 2-2.3: USB disconnect, address 8
May 24 15:45:04 localhost kernel: Stopping tasks: 
=================================================
====================================================|
May 24 15:45:04 localhost kernel: usb-storage 2-2.4:1.0: resume is unsafe!
May 24 15:45:04 localhost kernel: usblp 2-2.2:1.1: resume is unsafe!
May 24 15:45:04 localhost kernel: Warning: CPU frequency is 1400000, cpufreq 
assumed 600000 kHz.
May 24 15:45:04 localhost kernel: ehci_hcd 0000:00:1d.7: USB 2.0 restarted, 
EHCI 1.00, driver 10 De
c 2004
May 24 15:45:04 localhost kernel: ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 
11 (level, low) -> IRQ
 11
May 24 15:45:04 localhost kernel: ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 
11 (level, low) -> IRQ
 11
May 24 15:45:05 localhost kernel: ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 
11 (level, low) -> IRQ
 11
May 24 15:45:05 localhost kernel: ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 
11 (level, low) -> IRQ
 11
May 24 15:45:05 localhost kernel: psmouse.c: TouchPad at isa0060/serio1/input0 
lost sync at byte 1
May 24 15:45:05 localhost kernel: hub 2-2:1.0: hub_port_status failed (err = 
-113)
May 24 15:45:05 localhost last message repeated 3 times
May 24 15:45:05 localhost kernel: hub 2-2:1.0: activate --> -113
May 24 15:45:05 localhost kernel: hub 2-2:1.0: cannot disable port 2 (err = 
-113)
May 24 15:45:05 localhost kernel: hub 2-2:1.0: cannot disable port 3 (err = 
-113)
May 24 15:45:05 localhost kernel: hub 2-2:1.0: cannot disable port 4 (err = 
-113)
May 24 15:45:05 localhost kernel: Restarting tasks...<6>usb 2-2: USB 
disconnect, address 6
May 24 15:45:05 localhost kernel: usb 2-2.2: USB disconnect, address 7
May 24 15:45:05 localhost kernel: drivers/usb/class/usblp.c: usblp0: removed
May 24 15:45:05 localhost kernel:  done

'May 24 15:45:05 localhost kernel: usb 2-2.4: USB disconnect, address 9
May 24 15:45:05 localhost hal.hotplug[9683]: DEVPATH is not set
May 24 15:45:05 localhost kernel: sda : READ CAPACITY failed.
May 24 15:45:05 localhost kernel: sda : status=0, message=00, host=1, 
driver=00
May 24 15:45:05 localhost kernel: sda : sense not available.
May 24 15:45:05 localhost kernel: sda: Write Protect is off
May 24 15:45:05 localhost kernel: sda: assuming drive cache: write through
May 24 15:45:12 localhost cups: cupsd -HUP succeeded
May 24 15:45:12 localhost fstab-sync[9866]: removed mount 
point /mnt/LEXAR_MEDIA for /dev/sda1
May 24 15:45:49 localhost usb: USB-Controller (uhci-hcd) wird initialisiert:  
succeeded
May 24 15:45:49 localhost usb: USB-Controller (ehci-hcd) wird initialisiert:  
succeeded
May 24 15:45:49 localhost usb: Laden des USB-Druckers succeeded
May 24 15:46:05 localhost usb: USB-Controller (uhci-hcd) wird initialisiert:  
succeeded
May 24 15:46:05 localhost usb: USB-Controller (ehci-hcd) wird initialisiert:  
succeeded
May 24 15:46:05 localhost usb: Laden des USB-Druckers succeeded
[root@localhost pisti]# mousedrake
FATAL: Module hid not found.
FATAL: Module hid not found.
FATAL: Module mousedev not found.
FATAL: Module mousedev not found.
[root@localhost pisti]# service usb start
USB-Controller (uhci-hcd) wird initialisiert:                   [  OK  ]
USB-Controller (ehci-hcd) wird initialisiert:                   [  OK  ]
Laden des USB-Druckers                                          [  OK  ]'

Danach geht Geht die Maus nicht mehr. 



 Gruß,
 Istvan