Re: Bridge IP not anwering
"Fernando Rodriguez" <frod-Y20lP/[email protected]> Sat, 3 Mar 2007 11:22:59 -0600
| Newsgroups | gmane.linux.network.bridge.ebtables.user |
|---|---|
| Message-ID | <007101c75db8$973d4890$988086c9@sam> |
I currently have no rules for iptables or ebtables is this the reazon of why i cant ping or access the bridge via its ip?? -----Mensaje original----- De: ebtables-user-bounces-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org [mailto:ebtables-user-bounces-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org] En nombre de Turon Ivo ing. Enviado el: Jueves, 01 de Marzo de 2007 03:31 p.m. Para: [email protected] Asunto: Re: [Ebtables-user] Bridge IP not anwering You didn't write anything about iptables setting. This could be problem what is your iptables setting ? Did you allow input and output for that ping partner ? -----Original Message----- From: ebtables-user-bounces-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org [mailto:ebtables-user-bounces-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org]On Behalf Of Fernando Rodriguez Sent: Thursday, March 01, 2007 10:03 PM To: [email protected] Subject: [Ebtables-user] Bridge IP not anwering Hello, I have set up a bridge with the following script that starts after the network interfaces are started BRIDGENAME="BRQ" GATEWAY="192.168.0.1" BRIDGE_IP="192.168.0.122" BRIDGE_NETMASK="255.255.255.0" STP_ON="yes" STP_PRIO="1" RETVAL=0 start() { echo "Starting service bridge" ifconfig eth2 promisc up ifconfig eth3 promisc up brctl addbr $BRIDGENAME || return=$rc_failed brctl addif $BRIDGENAME eth2 || return=$rc_failed brctl addif $BRIDGENAME eth3 || return=$rc_failed ifconfig eth2 0.0.0.0 || return=$rc_failed ifconfig eth3 0.0.0.0 || return=$rc_failed brctl sethello $BRIDGENAME 1 || return=$rc_failed brctl setmaxage $BRIDGENAME 4 || return=$rc_failed brctl setfd $BRIDGENAME 4 || return=$rc_failed brctl stp $BRIDGENAME $STP_ON brctl setbridgeprio $BRIDGENAME $STP_PRIO ifconfig $BRIDGENAME $BRIDGE_IP netmask $BRIDGE_NETMASK up ip route flush cache ip route add default via $GATEWAY But the problem i have is that i am not able to contact the bridge on its IP 192.168.0.122 i am running Centos 4.4 on a 2.6.18 kernel, i have tested this setup on 3 different sets of network cards tg3, b44, via-rhine and in all of them i have the same results no connection, i know the bridge is working otherwise packets couldnt flow on the network, im using bridge utils 1.0.4-4 If any one knows what could be wrong?? Or does any one has a script or an example on how they set up their bridge in order to be able to access it via its IP?? Do i have to use ebtables to achieve this?? Thanks -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Ebtables-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ebtables-user ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Ebtables-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ebtables-user -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV