Re: [PATCH net] vxlan: mdb: Fix use-after-free in vxlan_mdb_flush()

On Sat, Aug 15, 2026 at 12:35:47AM +0900, Baul Lee wrote:
> vxlan_mdb_flush() iterates over the MDB entries using
> hlist_for_each_entry_safe(), which only tolerates the removal of the
> current entry. Contrary to the comment above the loop, the removal of an
> entry can trigger the removal of another entry.
> 
> Flushing the remotes of a (*, G) entry also removes the (S, G) entries
> that were created for its source list, once they are left without
> remotes:
> 
> vxlan_mdb_remotes_flush()
> -> vxlan_mdb_remote_del()
>    -> vxlan_mdb_remote_srcs_del()
>       -> vxlan_mdb_remote_src_del()
>          -> vxlan_mdb_remote_src_fwd_del()
>             -> __vxlan_mdb_del()
>                -> vxlan_mdb_entry_put()
> 
> Such an entry can be located after the (*, G) entry in the list, as
> vxlan_mdb_entry_get() returns an existing entry without moving it to the
> head of the list. This order is obtained by adding the (S, G) entry
> before the (*, G) entry, the latter with NLM_F_REPLACE, as the addition
> of the source otherwise fails with -EEXIST. The (S, G) entry is then the
> entry saved by hlist_for_each_entry_safe() and it is freed while the
> (*, G) entry is processed. The next iteration calls hlist_del() on it
> again, writing LIST_POISON1 to LIST_POISON2 [1].
> 
> Besides device deletion, the flush is also reachable from RTM_DELMDB
> with NLM_F_BULK.
> 
> Fix by re-reading the next entry after the remotes were flushed. The
> current entry cannot be removed by this flush, as source lists can only
> be configured on (*, G) entries and the removed entries are (S, G)
> entries. It is therefore still linked and its next pointer reflects the
> removals.
> 
> [1]
> BUG: KASAN: wild-memory-access in vxlan_mdb_entry_put.part.0+0x328/0x588
> Write of size 8 at addr dead000000000122 by task ip/327
> 
> CPU: 3 UID: 1000 PID: 327 Comm: ip Not tainted 7.2.0-rc7 #2 PREEMPT
> Call trace:
>  vxlan_mdb_entry_put.part.0+0x328/0x588
>  vxlan_mdb_flush+0x1d8/0x25c
>  vxlan_mdb_fini+0x8c/0x100
>  vxlan_uninit+0x1c/0x7c
>  unregister_netdevice_many_notify+0x954/0xd4c
>  rtnl_dellink+0x210/0x530
>  rtnetlink_rcv_msg+0x434/0x4d0
>  netlink_rcv_skb+0xc4/0x204
>  rtnetlink_rcv+0x18/0x24
>  netlink_unicast+0x4b8/0x548
>  netlink_sendmsg+0x29c/0x560
>  ____sys_sendmsg+0x390/0x3ec
>  ___sys_sendmsg+0x114/0x188
>  __sys_sendmsg+0xf0/0x178
>  __arm64_sys_sendmsg+0x48/0x60
>  invoke_syscall.constprop.0+0x58/0x180
>  el0_svc_common.constprop.0+0x74/0x140
>  do_el0_svc+0x30/0x40
>  el0_svc+0x38/0x98
>  el0t_64_sync_handler+0xa0/0xe4
>  el0t_64_sync+0x198/0x19c
> 
> Fixes: a3a48de5eade ("vxlan: mdb: Add MDB control path support")
> Signed-off-by: Baul Lee <[email protected]>

Reviewed-by: Ido Schimmel <[email protected]>