Assistance with nProbe with Accolade Cards

--===============0021299207408557358==
Content-Type: multipart/alternative; boundary="00000000000088c27b0592343dd7"

--00000000000088c27b0592343dd7
Content-Type: text/plain; charset="UTF-8"

Hello Everyone,

I am trying parse GTPv2 traffic using nProbe, PF_RING for Accolade Cards.
We also have purchased the GTPv2 plugin.

Currently, my nprobe config file looks like this:
-g=/var/run/nprobe.pid
-G=
-i=anic:0
-n=none
--dump-path=/var/log/nprobe
--cpu-affinity=2,3,4,5
--discard-unknown-flows=1
--verbose=2
--dump-format=b
--capture-direction=1
--drop-flow-no-plugin
--imsi-aggregation
--aggregate-gtp-tunnels

I am not sure how to check which accolade card is being used currently. Is
there is way someone can point me to figure out which accolade card number
to use in the interface section  of the nprobe.conf file.

Also I need to see the entire IP packet after it has been parsed by nProbe.
I need to dump the file in the local disk as well.

I will be more than happy to provide more information if required.

Thanks and Regards,
-=Srijan Nandi

--00000000000088c27b0592343dd7
Content-Type: text/html; charset="UTF-8"
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr"><div dir=3D"ltr">Hello Everyone,<div><br></div><div>I am t=
rying parse GTPv2 traffic using nProbe, PF_RING for Accolade Cards. We also=
 have purchased the GTPv2 plugin.</div><div><br></div><div>Currently, my np=
robe config file looks like this:</div><div><div>-g=3D/var/run/nprobe.pid</=
div><div>-G=3D</div><div>-i=3Danic:0</div><div>-n=3Dnone</div><div>--dump-p=
ath=3D/var/log/nprobe</div><div>--cpu-affinity=3D2,3,4,5</div><div>--discar=
d-unknown-flows=3D1</div><div>--verbose=3D2</div><div>--dump-format=3Db</di=
v><div>--capture-direction=3D1</div><div>--drop-flow-no-plugin</div><div>--=
imsi-aggregation</div><div>--aggregate-gtp-tunnels</div><div><br></div><div=
>I am not sure how to check which accolade card is being used currently. Is=
 there is way someone can point me to figure out which accolade card number=
 to use in the interface section =C2=A0of the nprobe.conf file.</div><div><=
br></div><div>Also I need to see the entire IP packet after it has been par=
sed by nProbe. I need to dump the file in the local disk as well.</div><div=
><br></div><div>I will be more than happy to provide more information if re=
quired.</div><div><br></div><div>Thanks and Regards,</div><div>-=3DSrijan N=
andi</div></div></div></div>

--00000000000088c27b0592343dd7--

--===============0021299207408557358==
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________
Ntop mailing list
[email protected]
http://listgateway.unipi.it/mailman/listinfo/ntop
--===============0021299207408557358==--