Re: Linux on Toradex Colibri PXA320
Semakin Dennis <[email protected]>
| Newsgroups | gmane.linux.ports.arm.general |
|---|---|
| Message-ID | <[email protected]> |
18.11.09, 18:05, "Daniel Mack" <[email protected]>: > On Wed, Nov 18, 2009 at 05:58:15PM +0100, Marek Vasut wrote: > > Dne St 18. listopadu 2009 14:53:10 Daniel Mack napsal(a): > > > On Wed, Nov 18, 2009 at 06:40:56AM -0600, Eric Miao wrote: > > > > 2009/11/18 Семакин Денис : > > > > > > > > 2. There are some problems with networking. When I ping the host, > > > > > passes a lot of time to host "ping-reply". There is only one switch > > > > > between my host and board with Linux. All settings (ip, route, etc...) > > > > > are correct. Telnet works with very small speed. What is problem? Is it > > > > > driver problem or MII interface problem? NIC driver is ax88796, which > > > > > is used only Remote DMA mode. > > > > > > That's something I never heard about. Ethernet was working properly here > > > ever since I tried it. More information would indeed be important. > > > > Maybe you don't have MAC address set properly for the card ? Some networking > > hardware can have problems with MAC that's all zeroes... > > In that case, the kernel should make up a random MAC. Anyway, the kernel > log output will tell. > > Daniel > Thanks everybody. Here is dmesg output log. The list is not complete, but the bacic moments I think are shown //begin Toradex Windows CE Bootloader 3.4 BETA 4 for Colibri Built Sep 22 2009 Press [SPACE] to enter Bootloader Menu Module HW V1.2E SerialNb: 2215423 NAND Flash K9K: 1003 MB, SDRAM: 128 MB Core Voltage: 1400 mV CPU: PXA320 806 (403), HSIO: 208, MEM: 208, DDRRAM: 260, SRAM: 312, LCD: 208 Set MAC: 00:14:2D:21:CD:FF Linux image found. Copying IMAGE(1951624) from FLASH(00081000) to RAM(80100000), using ECC... Jumping to image at 0x80100000... Uncompressing Linux............................................................. ............................................................ done, booting the kernel. <5>[ 0.000000] Linux version 2.6.31 (den@localhost) (gcc version 4.2.4) #331 Wed Nov 18 13:13:37 MSK 2009 <4>[ 0.000000] CPU: XScale-V3 based processor [69056826] revision 6 (ARMv5TE) , cr=0000397f <4>[ 0.000000] CPU: VIVT data cache, VIVT instruction cache <4>[ 0.000000] Machine: Toradex Colibri PXA320 <4>[ 0.000000] Memory policy: ECC disabled, Data cache writeback <7>[ 0.000000] On node 0 totalpages: 32768 <7>[ 0.000000] free_area_init_node: node 0, pgdat c03bee28, node_mem_map c03f 4000 <7>[ 0.000000] Normal zone: 256 pages used for memmap <7>[ 0.000000] Normal zone: 0 pages reserved <7>[ 0.000000] Normal zone: 32512 pages, LIFO batch:7 <6>[ 0.000000] RO Mode clock: 60.00MHz (inactive) <6>[ 0.000000] Run Mode clock: 403.00MHz (*31) <6>[ 0.000000] Turbo Mode clock: 806.00MHz (*2, active) <6>[ 0.000000] HSIO bus clock: 208.00MHz <4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 <5>[ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootdelay=5 <4>[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) <6>[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) <6>[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.000000] Memory: 128MB = 128MB total <5>[ 0.000000] Memory: 125752KB available (3516K code, 379K data, 108K init, 0K highmem) <6>[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1 , Nodes=1 <6>[ 0.000000] NR_IRQS:192 <4>[ 2.906704] Console: colour dummy device 80x30 <6>[ 2.963112] console [tty0] enabled <6>[ 3.007195] Calibrating delay loop... 804.45 BogoMIPS (lpj=4022272) <6>[ 3.305641] Security Framework initialized <4>[ 3.357872] Mount-cache hash table entries: 512 <6>[ 3.415744] CPU: Testing write buffer coherency: failed, enabling work-aro und <6>[ 3.508088] XScale3 L2 cache enabled. <6>[ 3.555930] NET: Registered protocol family 16 <6>[ 3.615891] colibri_pxa3xx_init_eth(): no valid serial boot tag found, tak ing MAC from device <6>[ 3.721918] [DDD] Set Calc: 800x600x60 mode <4>[ 3.784387] bio: create slab <bio-0> at 0 <5>[ 3.836826] SCSI subsystem initialized <6>[ 3.885505] usbcore: registered new interface driver usbfs <6>[ 3.955598] usbcore: registered new interface driver hub <6>[ 4.022662] usbcore: registered new device driver usb <6>[ 4.087428] NET: Registered protocol family 8 <6>[ 4.142793] NET: Registered protocol family 20 <6>[ 4.200769] NET: Registered protocol family 2 <6>[ 4.256133] Switched to NOHz mode on CPU #0 <6>[ 4.309513] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 4.395380] TCP established hash table entries: 4096 (order: 3, 32768 byte s) <6>[ 4.483232] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 4.563667] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 4.643058] TCP reno registered <6>[ 4.683902] NET: Registered protocol family 1 <4>[ 4.739685] NetWinder Floating Point Emulator V0.97 (double precision) <6>[ 4.835058] JFFS2 version 2.2. (NAND) A╘ 2001-2006 Red Hat, Inc. <6>[ 4.911837] JFS: nTxBlock = 983, nTxLock = 7869 <6>[ 4.973365] alg: No test for stdrng (krng) <6>[ 5.025699] io scheduler noop registered <6>[ 5.075945] io scheduler anticipatory registered <6>[ 5.134548] io scheduler deadline registered <6>[ 5.189077] io scheduler cfq registered (default) <4>[ 5.543932] Console: switching to colour frame buffer device 100x37 <6>[ 5.629590] PXA Overlay driver loaded successfully! <6>[ 5.943183] pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART <6>[ 6.031487] pxa2xx-uart.0: ttyS0 at MMIO 0x40200000 (irq = 21) is a BTUART <6>[ 6.031487] pxa2xx-uart.0: ttyS0 at MMIO 0x40700000 (irq = 20) is a STUART ax88796 ax88796.): 16bit, irq 100, c891a000, MAC 00:ff:ff:ff:ff:ff console [netcon0] enabled netconsole: network logging started NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Scanning device for bad blocks command execution timed out Bad eraseblock 0 at 000000000000 Creating 4 MTD partitions on "NAND 1CiB 3,3V 8 bit": 0x000000000000-0x000000080000 : "bootloader" 0x000000080000-0x000000480000 : "kernel" 0x000000480000-0x000000580000 : "reserved" 0x000000580000-0x000040000000 : "fs" usbmon: debugfs is not available ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver pxa27x-ohci pxa27x-ohci: PXA27x OHCI pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1 pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c000000 usb usb1: New USB device found, idVendor=1d6b, idProduct=2, SerialNumber=1 usb usb1: New USB device strings: Mfr-3, Product=2, SerialNumber=1 usb usb1: Product: PXA27x OHCI usb usb1: Manufactured: Linux 2.6.31 ohci_hcd usb usb1: SerialNumber: pxa27x usb usb1: configuration #1 chosen from choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected //end _______________________________________________ linux-arm mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm