[PATCH 4/7] serial: qcom-geni: Use geni_se_set_rate() for source clock configuration

The driver calls dev_pm_opp_set_rate() directly on uport->dev to apply
the computed source clock frequency, and dispatches baud rate handling
through a per-variant dev_data->set_rate() callback that either
recalculates the clock divider (Linux clock managed path) or selects
a performance level via geni_se_set_perf_level() (SA8255P firmware
managed path).

Now that geni_se_domain_attach() populates se->clk_perf_tbl from the
perf domain's OPP table, geni_se_clk_freq_match() can resolve a source
clock frequency and divider on the SA8255P path the same way it
already does for the Linux clock managed path. This removes the need
for a separate perf-level based set_rate implementation, so
geni_serial_set_rate() can be called unconditionally and
dev_data->set_rate can be dropped.

Switch to calling geni_serial_set_rate() directly from
qcom_geni_serial_set_termios(), and use geni_se_set_rate() in place of
dev_pm_opp_set_rate() so the frequency is applied to the correct
device (the perf domain device on the firmware managed path, or
uport->dev otherwise) without the driver needing to know which
resources_init variant is in use. Remove the now-unused set_rate field
from struct qcom_geni_device_data and its per-variant initializers.

Signed-off-by: Praveen Talari <[email protected]>
---
 drivers/tty/serial/qcom_geni_serial.c | 19 +++++++++----------
 1 file changed, 9 insertions(+), 10 deletions(-)

diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index 3633723acef8..cd1940eae084 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -114,7 +114,6 @@ struct qcom_geni_device_data {
 	bool console;
 	enum geni_se_xfer_mode mode;
 	int (*resources_init)(struct geni_se *se);
-	int (*set_rate)(struct geni_se *se, unsigned long baud);
 	int (*power_on)(struct geni_se *se);
 	int (*power_off)(struct geni_se *se);
 };
@@ -1474,7 +1473,10 @@ static int geni_serial_set_rate(struct geni_se *se, unsigned long baud)
 
 	uport->uartclk = clk_rate;
 	port->clk_rate = clk_rate;
-	dev_pm_opp_set_rate(uport->dev, clk_rate);
+	ret = geni_se_set_rate(&port->se, clk_rate);
+	if (ret)
+		return ret;
+
 	ser_clk_cfg = SER_CLK_EN;
 	ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
 
@@ -1513,7 +1515,7 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
 	/* baud rate */
 	baud = uart_get_baud_rate(uport, termios, old, 300, 8000000);
 
-	ret = port->dev_data->set_rate(&port->se, baud);
+	ret = geni_serial_set_rate(&port->se, baud);
 	if (ret)
 		return;
 
@@ -2040,6 +2042,8 @@ static int __maybe_unused qcom_geni_serial_runtime_suspend(struct device *dev)
 {
 	struct qcom_geni_serial_port *port = dev_get_drvdata(dev);
 
+	geni_se_set_rate(&port->se, 0);
+
 	return port->dev_data->power_off ?
 	       port->dev_data->power_off(&port->se) : 0;
 }
@@ -2047,7 +2051,6 @@ static int __maybe_unused qcom_geni_serial_runtime_suspend(struct device *dev)
 static int __maybe_unused qcom_geni_serial_runtime_resume(struct device *dev)
 {
 	struct qcom_geni_serial_port *port = dev_get_drvdata(dev);
-	struct uart_port *uport = &port->uport;
 	int ret;
 
 	if (port->dev_data->power_on) {
@@ -2056,8 +2059,8 @@ static int __maybe_unused qcom_geni_serial_runtime_resume(struct device *dev)
 			return ret;
 	}
 
-	if (port->se.has_opp && port->clk_rate)
-		return dev_pm_opp_set_rate(uport->dev, port->clk_rate);
+	if (port->clk_rate)
+		return geni_se_set_rate(&port->se, port->clk_rate);
 
 	return 0;
 }
@@ -2116,7 +2119,6 @@ static const struct qcom_geni_device_data qcom_geni_console_data = {
 	.console = true,
 	.mode = GENI_SE_FIFO,
 	.resources_init = geni_se_resources_init,
-	.set_rate = geni_serial_set_rate,
 	.power_on = geni_se_resources_activate,
 	.power_off = geni_se_resources_deactivate,
 };
@@ -2125,7 +2127,6 @@ static const struct qcom_geni_device_data sa8255p_qcom_geni_console_data = {
 	.console = true,
 	.mode = GENI_SE_FIFO,
 	.resources_init = geni_se_domain_attach,
-	.set_rate = geni_se_set_perf_level,
 };
 #endif
 
@@ -2133,7 +2134,6 @@ static const struct qcom_geni_device_data qcom_geni_uart_data = {
 	.console = false,
 	.mode = GENI_SE_DMA,
 	.resources_init = geni_se_resources_init,
-	.set_rate = geni_serial_set_rate,
 	.power_on = geni_se_resources_activate,
 	.power_off = geni_se_resources_deactivate,
 };
@@ -2142,7 +2142,6 @@ static const struct qcom_geni_device_data sa8255p_qcom_geni_uart_data = {
 	.console = false,
 	.mode = GENI_SE_DMA,
 	.resources_init = geni_se_domain_attach,
-	.set_rate = geni_se_set_perf_level,
 };
 
 static const struct dev_pm_ops qcom_geni_serial_pm_ops = {

-- 
2.34.1