System Freeze Kernel 2.6.18

"Alexander Schanz" <[email protected]>
Newsgroups gmane.linux.ports.hppa
Message-ID <[email protected]>
Dear Kernel ‚Hacker’s’,

we have some issues with Kernel 2.6.18-rc1-pa3 and all other ‚released’
kernel.

The System is a B2000 with two additional PCI_Cards:

Slot 2 Intel Ethernet card using e100 Module
Slot 3 Matrox G450 using the xsvc (XIG X-Server ported to Linux)

The System freezes after 2-5 days Running . (PMI Follows)

While the PMI indicates a problem when communicating with the Device in
Slot 3 of the PCI-Bus (The Matrox card)
we would like to gather more information about the problem.

Is there anyone with a Idea out there?

PMI of the System:

20-23   000088e54be588e5  0000000002000000  0000000000003962 
0000000000000000
24-27   0000000000003962  0000000000000000  00000000064b0000 
00000000006ff9d0
28-31   00000000ffffffff  00000000c05c5fa0  00000000c05c6300 
0000000000506443

<Press any key to continue (q to quit)>

Control Registers 0 - 31
00-03   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
04-07   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
08-11   000000000000112a  0000000000000000  00000000000000c0 
000000000000001d
12-15   0000000000000000  0000000000000000  000000000010b000 
00000000ff800000
16-19   000178776b3bda68  0000000000000895  000000000016e677 
0000000048f33c28
20-23   00000000a627ffe6  40000000004e9e14  000000ff0006ff0f 
0000000080000000
24-27   00000000005e5000  0000000015588000  0000000000044021 
00000000f0412000
28-31   0000000055555555  0000000055555555  0000000025580000 
000000001064c000
Space Registers 0 - 7

00-03   00000000          00000000          00000000          00000895
04-07   00000895          00000895          00000895          00000895

<Press any key to continue (q to quit)>

IIA Space                    = 0x0000000000000895
IIA Offset                   = 0x000000000016e67b
Check Type                   = 0x20000000
CPU State                    = 0x9e000004
Cache Check                  = 0x00000000
TLB Check                    = 0x00000000
Bus Check                    = 0x0030103b
Assists Check                = 0x00000000
Assist State                 = 0x00000000
Path Info                    = 0x00000000
System Responder Address     = 0x000000fff9801e14
System Requestor Address     = 0xfffffffffffa0000

Floating-Point Registers 0 - 31
00-03   0000001f00000000  0000000000000000  0000000000000000 
0000000000000000
04-07   40790d8178ce14fc  3fdfeebfc165b5db  0000000140000000 
3fa09ade97c43fd8
08-11   3fcf699399ac111b  4022000000000000  c045800000000000 
1452a200a0000000
12-15   000000051054b010  0000008810186418  1054aa241052e810 
10691810f0400004
16-19   00000000000000d0  10d1898000000000  1054aa243b9aca00 
eff3f84000000000
20-23   10d38000fffff000  10d4b73010182614  0000000000000660 
0000000c00000000
24-27   0000002000000000  0000008800000000  3ff90d817c5fcd4e 
3fe90d8178ce14fc
28-31   3fefffffffecc1dd  3ff46e579ad0c47a  3fe39d2000000000 
c02c000000000000

<Press any key to continue (q to quit)>


'9000/785 B,C,J Workstation Unarchitected (per-CPU)', rev 1, 140 bytes:

Check Summary                = 0xcb81041008000000
Available Memory             = 0x0000000020000000
CPU Diagnose Register 2      = 0x0300000000000004
CPU Status Register 0        = 0x2420c20000000000
CPU Status Register 1        = 0x8002000000000000
SADD LOG                     = 0x00c0000000000000
Read Short LOG               = 0xc1a0f0fff9801e14
ERROR_STATUS                 = 0x0000000000100010
MEM_ADDR                     = 0x000001ff3fffffff
MEM_SYND                     = 0x0000000000000000
MEM_ADDR_CORR                = 0x000001ff3fffffff
MEM_SYND_CORR                = 0x0000000000000000
RUN_DATA_HIGH                = 0xc1bff0fffed08040
RUN_DATA_LOW                 = 0xc1bff0fffed08040
RUN_CTRL                     = 0x0000021c00001418
RUN_ADDR                     = 0xc1bff0fffed08040
System Responder Path        = 0x00ffff0a01030000


HPMC PIM Analysis Information:

Timestamp =
  Fri Nov  24 13:59:28 GMT 2006    (20:06:11:24:13:59:28)


'9000/785 B,C,J Workstation HPMC PIM Analysis (per-CPU)', rev 0, 1304 bytes:

A Data I/O Fetch Timeout occurred while CPU 0 was
requesting information from a device at the path 10/1/3/0/0 (PCI slot 3).


Memory/IO Controller Error Analysis Information:

The Memory/IO Controller only observed the Broadcast Error.  It did not log
any additional information about the HPMC.

<Press any key to continue (q to quit)>

-----------------  Processor 0 LPMC Information ------------------

Check Type                   = 0x00000000
I/D Cache Parity Info        = 0x00000000
Cache Check                  = 0x00000000
TLB Check                    = 0x00000000
Bus Check                    = 0x00000000
Assists Check                = 0x00000000
Assist State                 = 0x00000000
Path Info                    = 0x00000000
System Responder Address     = 0x0000000000000000
System Requestor Address     = 0x0000000000000000


-----------------  Processor 0 TOC Information -------------------

General Registers 0 - 31
00-03   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
04-07   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
08-11   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
12-15   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
16-19   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
20-23   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
24-27   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
28-31   0000000000000000  0000000000000000  0000000000000000 
0000000000000000

<Press any key to continue (q to quit)>

Control Registers 0 - 31
00-03   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
04-07   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
08-11   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
12-15   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
16-19   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
20-23   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
24-27   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
28-31   0000000000000000  0000000000000000  0000000000000000 
0000000000000000
Space Registers 0 - 7

00-03   00000000          00000000          00000000          00000000
04-07   00000000          00000000          00000000          00000000

IIA Space                    = 0x0000000000000000
IIA Offset                   = 0x0000000000000000
CPU State                    = 0x00000000


<Press any key to continue (q to quit)>

Memory Error Log Information:

Timestamp =
  Fri Nov  24 13:59:28 GMT 2006    (20:06:11:24:13:59:28)


'9000/785 B,C,J Workstation Memory Error Log', rev 0, 64 bytes:

   No memory errors logged


I/O Module Error Log Information:

Timestamp =
  Fri Nov  24 13:59:28 GMT 2006    (20:06:11:24:13:59:28)


'9000/785 B,C,J Workstation IO Error Log', rev 0, 228 bytes:

 Rope     Word1        Word2            Word3
------ ------------ ------------
   0    0x00000000   0x0e0cc009   0x00000000fed30048
   1    0x00000000   0x1e0cc249   0x00000000fed32048
   2    ----------   0x2e0cc009   ------------------
   3    ----------   0x3e0cc009   ------------------
   4    ----------   0x4e0cc009   ------------------
   5    ----------   0x5e0cc009   ------------------
   6    ----------   0x6e0cc009   ------------------
   7    ----------   0x7e0cc009   ------------------
Service Menu: Enter command >
Service Menu: Enter command >
Service Menu: Enter command >
Service Menu: Enter command > pdt

PAGE DEALLOCATION TABLE INFORMATION

     Address     Error Type  Perm  Slot
   ------------  ----------  ----  ----

   No entries in Page Deallocation Table

   PDT has 50 free entries
   PDT Reset Clear Flag is Set
   PDT Interleaving Changed Flag is Clear


Regards,

Alexander Schanz
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.