Re: [PATCH v2 10/13] PCI/CXL: Clear ACS SV across an SBR of a CXL DPort

On Tue, Aug 25, 2026 at 04:26:25AM +0800, Fabio M. De Francesco wrote:
> A Secondary Bus Reset (SBR) of a CXL Downstream Port clears the
> Downstream Component's (DPort) captured Bus Number. CXL r4.0 sec 8.1.5.1
> notes that if a Downstream Component issues PM Init messages to a DPort
> with Access Control Services (ACS) Source Validation (SV) bit enabled,
> PM Initialization may then fail to complete, and that a further SBR
> alone does not recover it. PCIe r7.0 sec 6.12.1.1 makes that rejection
> an error that is a reported as ACS Violation.
> 
> Reuse the recovery sequence described in sec 8.1.5.1 but make it
> preventive, so that PM Init don't fail and don't need to be recovered.
> 
> Signed-off-by: Fabio M. De Francesco <[email protected]>
> ---
>  drivers/pci/pci.c             | 177 ++++++++++++++++++++++++++++++++--
>  include/uapi/linux/pci_regs.h |   2 +
>  2 files changed, 172 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> index 417b6b44473e..f3781d1e8f6e 100644
> --- a/drivers/pci/pci.c
> +++ b/drivers/pci/pci.c
> @@ -23,6 +23,7 @@
>  #include <linux/module.h>
>  #include <linux/spinlock.h>
>  #include <linux/string.h>
> +#include <linux/string_choices.h>
>  #include <linux/log2.h>
>  #include <linux/logic_pio.h>
>  #include <linux/device.h>
> @@ -4857,21 +4858,189 @@ void pci_cxl_set_sbr_region_ops(const struct pci_cxl_sbr_region_ops *ops)
>  }
>  EXPORT_SYMBOL_GPL(pci_cxl_set_sbr_region_ops);
>  
> +struct cxl_sbr_ctx {
> +	u16 port_ctl;
> +	u16 acs_ctrl;
> +	u16 command;
> +};
> +
> +static bool is_cxl_dport(struct pci_dev *dev)
> +{
> +	return pcie_is_cxl(dev) && pcie_downstream_port(dev);
> +}
> +
> +static u16 cxl_port_dvsec(struct pci_dev *dev)
> +{
> +	return pci_find_dvsec_capability(dev, PCI_VENDOR_ID_CXL,
> +					 PCI_DVSEC_CXL_PORT);
> +}
> +
> +static int cxl_sbr_prepare(struct pci_dev *bridge, u16 dvsec,
> +			   struct cxl_sbr_ctx *ctx)
> +{
> +	int rc;
> +
> +	/* Abort before touching hardware if the regions cannot be disabled. */
> +	if (cxl_sbr_region_ops) {
> +		rc = cxl_sbr_region_ops->disable_regions(bridge);
> +		if (rc)
> +			return rc;
> +	}
> +
> +	/* CXL r4.0 sec 8.1.5.2, Table 8-32: set Unmask SBR so the Port issues Hot Reset. */
> +	pci_read_config_word(bridge, dvsec + PCI_DVSEC_CXL_PORT_CTL, &ctx->port_ctl);
> +	pci_write_config_word(bridge, dvsec + PCI_DVSEC_CXL_PORT_CTL,
> +			      ctx->port_ctl | PCI_DVSEC_CXL_PORT_CTL_UNMASK_SBR);
> +
> +	pci_read_config_word(bridge, PCI_COMMAND, &ctx->command);
> +	pci_clear_master(bridge);
> +
> +	/* CXL r4.0 sec 8.1.5.1: Disable ACS SV bit before SBR */
> +	if (bridge->acs_cap) {
> +		pci_read_config_word(bridge, bridge->acs_cap + PCI_ACS_CTRL, &ctx->acs_ctrl);
> +		pci_dbg(bridge, "%s: ACS SV %s\n", __func__,
> +			str_enabled_disabled(ctx->acs_ctrl & PCI_ACS_SV));
> +		pci_write_config_word(bridge, bridge->acs_cap + PCI_ACS_CTRL,
> +				      ctx->acs_ctrl & ~PCI_ACS_SV);
> +	}
> +
> +	return 0;
> +}
> +
> +/*
> + * CXL r4.0 sec 8.1.5.1, Table 8-31: the Port sets PM Init Complete within
> + * 100 ms of link-up. Restoring ACS Source Validation before then makes the
> + * Port reject the downstream Component's Requester-Bus-0 IP2PM message, so
> + * poll for completion before restoring config.
> + */
> +static bool cxl_port_pm_init_is_complete(struct pci_dev *bridge, u16 dvsec)
> +{
> +	unsigned long start = jiffies;
> +	unsigned long timeout = start + msecs_to_jiffies(100);
> +	u16 status;
> +
> +	do {
> +		pci_read_config_word(bridge,
> +				     dvsec + PCI_DVSEC_CXL_PORT_EXT_STATUS,
> +				     &status);
> +		if (!PCI_POSSIBLE_ERROR(status) &&
> +		    (status & PCI_DVSEC_CXL_PORT_EXT_STATUS_PM_INIT_COMP)) {
> +			pci_dbg(bridge, "%s: PM Init Complete set after %u ms, ext status %#06x\n",
> +				__func__, jiffies_to_msecs(jiffies - start), status);
> +			return true;
> +		}
> +		msleep(10);
> +	} while (time_before(jiffies, timeout));
> +
> +	pci_warn(bridge, "%s: PM Init Complete not set after %u ms, ext status %#06x\n",
> +		 __func__, jiffies_to_msecs(jiffies - start), status);
> +
> +	return false;
> +}
> +
> +static int cxl_sbr_restore_config_space(struct pci_dev *dev, void *userdata)
> +{
> +	pci_restore_config_space(dev);
> +	pci_dbg(dev, "%s: config space restored\n", __func__);
> +
> +	return 0;
> +}
> +
> +/*
> + * The CXL region ops that run next read the HDM Decoders through a Base Address
> + * Register the reset returned to its initialization value, so restore the
> + * header of every device below @bridge first. Restoring also re-captures each
> + * Bus Number before the Port's ACS Source Validation comes back: a device that
> + * has completed no Type 0 Configuration Write since the reset sources Requests
> + * with Bus 0, which the Port rejects as an ACS Violation.
> + *
> + * Only the header is restored. The capability state each caller saved is its own
> + * to replay, and the ->reset_done() callbacks pci_dev_restore() invokes must
> + * fire once, from the caller that owns the reset.
> + */
> +static void cxl_sbr_restore_subordinate(struct pci_dev *bridge)
> +{
> +	if (!bridge->subordinate)
> +		return;
> +
> +	/* Parents before children: a child answers once its parent forwards. */
> +	pci_walk_bus(bridge->subordinate, cxl_sbr_restore_config_space, NULL);
> +}
> +
> +static void cxl_sbr_complete(struct pci_dev *bridge, u16 dvsec,
> +			     const struct cxl_sbr_ctx *ctx)
> +{
> +	u16 val;
> +
> +	/* CXL r4.0 sec 8.1.5.1: wait for PM Init before restoring ACS SV. */
> +	if (!cxl_port_pm_init_is_complete(bridge, dvsec))
> +		pci_warn(bridge,
> +			 "restoring ACS Source Validation before PM Init complete; Port may reject the Component's bus 0 traffic\n");
> +
> +	cxl_sbr_restore_subordinate(bridge);
> +
> +	/* CXL r4.0 sec 8.1.5.1: Re-enable ACS SV bit after SBR if it was enabled before */
> +	if (bridge->acs_cap && (ctx->acs_ctrl & PCI_ACS_SV)) {
> +		pci_read_config_word(bridge, bridge->acs_cap + PCI_ACS_CTRL, &val);
> +		pci_write_config_word(bridge, bridge->acs_cap + PCI_ACS_CTRL,
> +				      val | PCI_ACS_SV);
> +		pci_dbg(bridge, "%s: ACS SV bit set\n", __func__);
> +	} else {
> +		pci_dbg(bridge, "%s: ACS SV bit not set (was not enabled before the SBR)\n",
> +			__func__);
> +	}
> +
> +	if (ctx->command & PCI_COMMAND_MASTER)
> +		pci_set_master(bridge);
> +
> +	if (!(ctx->port_ctl & PCI_DVSEC_CXL_PORT_CTL_UNMASK_SBR)) {
> +		pci_read_config_word(bridge, dvsec + PCI_DVSEC_CXL_PORT_CTL, &val);
> +		pci_write_config_word(bridge, dvsec + PCI_DVSEC_CXL_PORT_CTL,
> +				      val & ~PCI_DVSEC_CXL_PORT_CTL_UNMASK_SBR);
> +	}
> +
> +	if (cxl_sbr_region_ops)
> +		cxl_sbr_region_ops->enable_regions(bridge);
> +}
> +
>  /**
>   * pci_bridge_secondary_bus_reset - Reset the secondary bus on a PCI bridge.
>   * @dev: Bridge device
>   *
>   * Use the bridge control register to assert reset on the secondary bus.
>   * Devices on the secondary bus are left in power-on state.
> + *
> + * When @dev is a CXL Downstream Port, clear ACS Source Validation and Bus
> + * Master Enable across the reset, per the workaround in CXL r4.0 sec 8.1.5.1,
> + * so that Port Power Management Initialization completes at link-up. The
> + * bits stay cleared until the secondary bus is back, then are restored.
>   */
>  int pci_bridge_secondary_bus_reset(struct pci_dev *dev)
>  {
> +	struct cxl_sbr_ctx ctx = {};
> +	u16 dvsec = 0;
> +	int rc;
> +
>  	if (!dev->block_cfg_access)
>  		pci_warn_once(dev, "unlocked secondary bus reset via: %pS\n",
>  			      __builtin_return_address(0));
> +
> +	if (is_cxl_dport(dev))
> +		dvsec = cxl_port_dvsec(dev);
> +	if (dvsec) {
> +		rc = cxl_sbr_prepare(dev, dvsec, &ctx);
> +		if (rc)
> +			return rc;
> +	}
> +
>  	pcibios_reset_secondary_bus(dev);
>  
> -	return pci_bridge_wait_for_secondary_bus(dev, "bus reset");
> +	rc = pci_bridge_wait_for_secondary_bus(dev, "bus reset");
> +
> +	if (dvsec)
> +		cxl_sbr_complete(dev, dvsec, &ctx);

Hi Fabio,

I wonder what happens if pci_bridge_wait_for_secondary_bus() fails here?

Maybe failures before/after SBR should be handled differenly ?

Before SBR, it's safe to undo preparation. After SBR, the HW state may be unknown,
in that case, enable_regions() must not reattach regions unless PCI state and all HDM
decoders were restored successfully.

Best regards,
Richard Cheng

> +
> +	return rc;
>  }
>  EXPORT_SYMBOL_GPL(pci_bridge_secondary_bus_reset);
>  
> @@ -4917,12 +5086,6 @@ static int pci_dev_reset_slot_function(struct pci_dev *dev, bool probe)
>  	return pci_reset_hotplug_slot(dev->slot->hotplug, probe);
>  }
>  
> -static u16 cxl_port_dvsec(struct pci_dev *dev)
> -{
> -	return pci_find_dvsec_capability(dev, PCI_VENDOR_ID_CXL,
> -					 PCI_DVSEC_CXL_PORT);
> -}
> -
>  static bool cxl_sbr_masked(struct pci_dev *dev)
>  {
>  	u16 dvsec, reg;
> diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h
> index facaa324bd86..0eaa34db93ce 100644
> --- a/include/uapi/linux/pci_regs.h
> +++ b/include/uapi/linux/pci_regs.h
> @@ -1371,6 +1371,8 @@
>  
>  /* CXL r4.0, 8.1.5: Extensions DVSEC for Ports */
>  #define PCI_DVSEC_CXL_PORT				3
> +#define  PCI_DVSEC_CXL_PORT_EXT_STATUS			0x0a
> +#define   PCI_DVSEC_CXL_PORT_EXT_STATUS_PM_INIT_COMP	0x00000001
>  #define  PCI_DVSEC_CXL_PORT_CTL				0x0c
>  #define   PCI_DVSEC_CXL_PORT_CTL_UNMASK_SBR		0x00000001
>  
> -- 
> 2.55.0
> 
>