Re: Where are all the patches and diffs available for 0.9.71preX?

Hi Joe,

I do have the sheep module compiled in.  I think I modified the 
molrc.network file to use the sheep module instead of the tun module.  I 
did not compile in the X11 XDGA support which was supposed to be 
outdated.  I didn't compile in the debugging, though maybe I should.  I 
did notice that it complained about not finding .traps.o.cmd for 
kmod/traps.o when I did make, under building modules, stage 2.

How do I make sure the old OF instead of the new OpenBios is actually 
being used?  The -V option doesn't seem to have been updated so that it 
says 0.9.71. 

I can't seem to see any difference between the pre6 and pre7 versions as 
far as how it operates.  I'm rather new to Linux.  Is there a 
development environment available in Linux that will allow me to 
highlight a function call in the source and click on it and  it  will 
take me to the function 's definition like you can do in  Xcode?

It starts the OS X installer CD just fine.  It starts the Tiger 
partition just fine.  It gets hung up after switching to the screen that 
is black with an underscore as a cursor assuming you haven't run 
molvconfig with the OS 9 installer cd and also with the internal OS 9 
partition.  If you have run molvconfig the screen is the one with the 
text on it from that program.

Thanks so much for the tips and assistance!

Rob

Joseph Jezak wrote:

> Rob Frohne wrote:
>
>> Hi Joe,
>>
>> I was quite excited to find your pre7 tarball, and downloaded it at 
>> school on a Lombard powerbook I have running ubuntu, and had 
>> previously got pre6 going on just fine with OS X.  I didn't have a 
>> lot of time to play with it, but it didn't work out of the box with 
>> OS 9 partition that had worked with a previous version of mol, though 
>> I think it worked with an OS X on CD.  I also just tried it on 
>> another powerbook here at home that I have kubuntu on and which was 
>> previously set up with pre6, and it boots OS X ok, but I can't get it 
>> to boot OS 9 off CD .  I also tried to boot OS 9 which is installed 
>> on the same partition as OS X 10.4.3.  It didn't get farther than 
>> loading the sheep driver, and the screen only showed the results from 
>> molvconfig.  Do I need to do more than  make, and make install as 
>> root to make OS 9 work?
>>
>> Thanks,
>>
>> Rob
>
>
> No, although I admit, I'm using the ebuild I wrote for Gentoo.  Make 
> sure that you've got the Sheep module turned on (make menuconfig in 
> the source root).
>
> Does it boot off of the OS9 CD instead of from the partition? Did you 
> change any of the configuration files at all?
>
> -Joe
> _______________________________________________
> mol-general mailing list
> [email protected]
> http://lists.maconlinux.org/mailman/listinfo/mol-general


-- 
Rob Frohne, Ph.D., P.E.
E.F. Cross School of Engineering
Walla Walla College
100 SW 4th Street
College Place, WA 99324
(509) 527-2075
http://www.wwc.edu/~frohro

_______________________________________________
mol-general mailing list
[email protected]
http://lists.maconlinux.org/mailman/listinfo/mol-general

begin:vcard
fn:Rob Frohne
n:Frohne;Rob
org:Walla Walla College;E.F. Cross School of Engineering
adr:;;100 SW 4th Street;College Place;WA;99324;USA
email;internet:[email protected]
title:Professor
tel;work:(509) 527-2075
tel;fax:(509) 527-2867
tel;home:(509) 529-3585
url:http://www.wwc.edu/~frohro
version:2.1
end:vcard