Re: [PATCH] sh: Avoid using IRQ0 on SH3 and SH4

John Paul Adrian Glaubitz <[email protected]>
Newsgroups gmane.linux.ports.sh.devel,gmane.linux.kernel
Message-ID <7b2c0d812280afaefee0c70a9aea00a0fcf84e3a.camel@physik.fu-berlin.de>
Hi Geert!

On Thu, 2023-07-06 at 17:39 +0200, Geert Uytterhoeven wrote:
> Which sh4 platforms in particular?
> 
> I booted a kernel with this patch on rts7751r2d (QEMU) and landisk
> (physical) two days ago.

I gave it a try with the command line Guenter suggested and indeed the kernel locks
up right here with the patch applied and boots fine without it:

Creating 4 MTD partitions on "physmap-flash":
0x000000000000-0x000000040000 : "U-Boot"
0x000000040000-0x000000080000 : "Environment"
0x000000080000-0x000000240000 : "Kernel"
0x000000240000-0x000001000000 : "Flash_FS"
8139too: 8139too Fast Ethernet driver 0.9.28
8139too 0000:00:01.0: This (id 10ec:8139 rev 20) is an enhanced 8139C+ chip, use 8139cp
sm501-usb sm501-usb: SM501 OHCI
sm501-usb sm501-usb: new USB bus registered, assigned bus number 1
sm501-usb sm501-usb: irq 116, io mem 0x13e40000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.04
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: SM501 OHCI
usb usb1: Manufacturer: Linux 6.4.0-12069-gc17414a273b8 ohci_hcd
usb usb1: SerialNumber: sm501-usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver usb-storage
rtc-r9701 spi0.0: cannot read RTC register
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered PF_PACKET protocol family
heartbeat: version 0.1.2 loaded
ata1: found unknown device (class 0)
(stops here)

Using rts7751r2dplus_defconfig and the following command line:

qemu-system-sh4 -M r2d -kernel vmlinuz-6.5-rc1 -hda debian_sid_sh4_standard.qcow2 -no-reboot -device rtl8139,netdev=net0 -netdev user,id=net0 -append "root=/dev/sda1 console=ttySC1,115200
earlycon=scif,mmio16,0xffe80000 noiotrap" -serial null -serial stdio -nographic -monitor null

And using this old qcow2 image:

> https://people.debian.org/~aurel32/qemu/sh4/debian_sid_sh4_standard.qcow2

Maybe it's a configuration issue if it works for you?

Adrian

-- 
 .''`.  John Paul Adrian Glaubitz
: :' :  Debian Developer
`. `'   Physicist
  `-    GPG: 62FF 8A75 84E0 2956 9546  0006 7426 3B37 F5B5 F913
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.