Re: [DO NOT MERGE v5 11/37] pci: pci-sh7751: Add SH7751 PCI driver

On Tue, Dec 5, 2023, at 10:45, Yoshinori Sato wrote:

> +#include <asm/addrspace.h>
> +#include "pci-sh7751.h"
> +
> +#define pcic_writel(val, base, reg) __raw_writel(val, base + (reg))
> +#define pcic_readl(base, reg) __raw_readl(base + (reg))

__raw_writel()/__raw_readl() has a number of problems with
atomicity (the compiler may split or merge pointer
dereferences), barriers and endianess. You should normally
always use readl()/writel() instead.

> +	memset(pci_config, 0, sizeof(pci_config));
> +	if (of_property_read_u32_array(np, "renesas,config",
> +				       pci_config, SH7751_NUM_CONFIG) == 0) {
> +		for (i = 0; i < SH7751_NUM_CONFIG; i++) {
> +			r = pci_config[i * 2];
> +			/* CONFIG0 is read-only, so make it a sentinel. */
> +			if (r == 0)
> +				break;
> +			pcic_writel(pci_config[i * 2 + 1], pcic, r * 4);
> +		}
> +	}

the config property seems a little too specific to this
implementation of the driver. Instead of encoding register
values in DT, I think these should either be described
in named properties where needed, or hardcoded in the driver
if there is only one sensible value.

> +/*
> + * We need to avoid collisions with `mirrored' VGA ports
> + * and other strange ISA hardware, so we always want the
> + * addresses to be allocated in the 0x000-0x0ff region
> + * modulo 0x400.
> + */
> +#define IO_REGION_BASE 0x1000
> +resource_size_t pcibios_align_resource(void *data, const struct 
> resource *res,
> +				resource_size_t size, resource_size_t align)
> +{

You can't have these generic functions in a driver, as that
prevents you from building more than one such driver.

The logic you have here is neither architecture nor
driver specific.

> +static int sh7751_pci_probe(struct platform_device *pdev)
> +{
> +	struct resource *res, *bscres;
> +	void __iomem *pcic;
> +	void __iomem *bsc;
> +	u32 memory[2];
> +	u16 vid, did;
> +	u32 word;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (IS_ERR(res))
> +		return PTR_ERR(res);
> +	pcic = (void __iomem *)res->start;

This cast is invalid, as res->start is a physical address
that you would need to ioremap() to turn into an __iomem
pointer.

> +	bscres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> +	bsc = devm_ioremap_resource(&pdev->dev, bscres);
> +	if (IS_ERR(bsc))
> +		return PTR_ERR(bsc);
> +
> +	if (of_property_read_u32_array(pdev->dev.of_node,
> +				       "renesas,memory", memory, 2) < 0) {
> +		/*
> +		 * If no memory range is specified,
> +		 *  the entire main memory will be targeted for DMA.
> +		 */
> +		memory[0] = memory_start;
> +		memory[1] = memory_end - memory_start;
> +	}

There is a generic "dma-ranges" proerty for describing
which memory is visible by a bus.

> diff --git a/drivers/pci/controller/pci-sh7751.h 
> b/drivers/pci/controller/pci-sh7751.h
> new file mode 100644
> index 000000000000..540cee7095c6
> --- /dev/null
> +++ b/drivers/pci/controller/pci-sh7751.h
> @@ -0,0 +1,76 @@

If the header is only included from one file, just removed
it and add the register definitions to the driver directly.

     Arnd