[PATCH v7 22/37] dt-bindings: display: smi,sm501: SMI SM501 binding json-schema

Signed-off-by: Yoshinori Sato <[email protected]>
---
 .../bindings/display/smi,sm501.yaml           | 398 ++++++++++++++++++
 1 file changed, 398 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/smi,sm501.yaml

diff --git a/Documentation/devicetree/bindings/display/smi,sm501.yaml b/Documentation/devicetree/bindings/display/smi,sm501.yaml
new file mode 100644
index 000000000000..06c6af4fa4a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/smi,sm501.yaml
@@ -0,0 +1,398 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/smi,sm501.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Motion SM501 Mobile Multimedia Companion Chip
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+description: |
+  These DT bindings describe the SM501.
+
+properties:
+  compatible:
+    const:
+      smi,sm501
+
+  reg:
+    maxItems: 2
+    description: |
+     First entry: System Configuration register
+     Second entry: IO space (Display Controller register)
+
+  interrupts:
+    description: SM501 interrupt to the cpu should be described here.
+
+  mode:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: select a video mode
+
+  edid:
+    description: |
+      verbatim EDID data block describing attached display.
+      Data from the detailed timing descriptor will be used to
+      program the display controller.
+
+  little-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: available on big endian systems, to set different foreign endian.
+  big-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: available on little endian systems, to set different foreign endian.
+
+  swap-fb-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: swap framebuffer byteorder.
+
+  route-crt-panel:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: Panel output merge to CRT.
+
+  crt:
+    type: object
+    description: CRT output control
+    properties:
+      edid:
+        $ref: /schemas/types.yaml#/definitions/uint8-array
+        description: |
+          verbatim EDID data block describing attached display.
+          Data from the detailed timing descriptor will be used to
+          program the display controller.
+
+      smi,flags:
+        $ref: /schemas/types.yaml#/definitions/string-array
+        description: Display control flags.
+        items:
+          anyOf:
+            - const: use-init-done
+            - const: disable-at-exit
+            - const: use-hwcursor
+            - const: use-hwaccel
+            - const: panel-no-fpen
+            - const: panel-no-vbiasen
+            - const: panel-inv-fpen
+            - const: panel-inv-vbiasen
+        maxItems: 8
+
+      bpp:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Color depth
+
+  panel:
+    type: object
+    description: Panel output control
+    properties:
+      edid:
+        $ref: /schemas/types.yaml#/definitions/uint8-array
+        description: |
+          verbatim EDID data block describing attached display.
+          Data from the detailed timing descriptor will be used to
+          program the display controller.
+
+      smi,flags:
+        $ref: /schemas/types.yaml#/definitions/string-array
+        description: Display control flags.
+        items:
+          anyOf:
+            - const: use-init-done
+            - const: disable-at-exit
+            - const: use-hwcursor
+            - const: use-hwaccel
+            - const: panel-no-fpen
+            - const: panel-no-vbiasen
+            - const: panel-inv-fpen
+            - const: panel-inv-vbiasen
+        maxItems: 8
+
+      bpp:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Color depth
+
+  smi,devices:
+    $ref: /schemas/types.yaml#/definitions/string-array
+    description: Select SM501 device functions.
+    items:
+      anyOf:
+        - const: usb-host
+        - const: usb-slave
+        - const: ssp0
+        - const: ssp1
+        - const: uart0
+        - const: uart1
+        - const: fbaccel
+        - const: ac97
+        - const: i2s
+        - const: gpio
+    minItems: 1
+    maxItems: 10
+
+  smi,mclk:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: mclk frequency.
+
+  smi,m1xclk:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: m1xclk frequency.
+
+  misc-timing:
+    type: object
+    description: Miscellaneous Timing register values.
+    properties:
+      ex:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Extend bus holding time.
+
+      xc:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Xscale clock input select.
+
+      usb-over-current-detect-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB host current detection disable (Us=0).
+
+      usb-over-current-detect-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB host current detection disable (Us=1).
+
+      sdram-clock-mode1-288mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM1 bit is clear.
+
+      sdram-clock-mode1-div:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM1 bit is set.
+
+      sm1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SDRAM clock divider for PW mode 1.
+
+      sdram-clock-mode0-288mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM0 bit is clear.
+
+      sdram-clock-mode0-div:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM0 bit is set.
+
+      sm0:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: SDRAM clock divider for PW mode 0.
+
+      pll-debug-input:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 96MHz PLL debug input reference frequency (Deb=0).
+
+      pll-debug-output:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 96MHz PLL debug output frequency (Deb=1).
+
+      no-acpi-control:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: No ACPI control (A=0).
+
+      acpi-control:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: No ACPI control (A=1).
+
+      divider:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Second PLL output frequency.
+
+      usb-host-normal:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB Host normal mode.
+
+      usb-host-simulation:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB Host simulation mode.
+
+      delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Delay time to latch read data. Set the value to 10x.
+
+  misc-control:
+    type: object
+    description: Miscellaneous Control register values.
+    properties:
+      pad:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: PCI Pad drive strength.
+
+      usbclk:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: USB Clcok Select.
+
+      uart1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: UART1 (SSP=0)
+
+      ssp1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSP1 (SSP=1)
+
+      latch-address-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 8051 Latch disable (Lat=0).
+
+      latch-address-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 8051 Latch enable (Lat=1).
+
+      panel-data-18bit:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Flat Panel data 18bit (FP=0).
+
+      panel-data-24bit:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Flat Panel data 24bit (FP=1).
+
+      xtal-freq-24mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Crystal frequency 24MHz (Freq=0).
+
+      xtal-freq-12mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Crystal frequency 12MHz (Freq=1).
+
+      refresh:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Internal memory refresh timing.
+
+      hold:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: BUS Hold time.
+
+      sh-ready-low:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SuperH ready polarity active low (SH=0).
+
+      sh-ready-high:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SuperH ready polarity active high (SH=1).
+
+      interrupt-normal:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Interrupt normal (II=0).
+
+      interrupt-inverted:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Interrupt Inverting (II=1).
+
+      pll-clock-count-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: PLL clock count disable.
+
+      pll-clock-count-enaable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: PLL clock count enable.
+
+      dac-power-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: DAC Power enable (DAC=0).
+
+      dac-power-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: DAC Power disable (DAC=1).
+
+      usb-slave-cpu:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB slave controller cpu (MC=0).
+
+      usb-slave-8051:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB slave controller 8051MCU (MC=1).
+
+      burst-length-8:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: CPU Master burst length 8 (BL=0).
+
+      burst-length-1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: CPU Master burst length 1 (BL=1).
+
+      usb-port-master:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB port master.
+
+      usb-port-slave:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB port slave.
+
+      vr-mmio-30mb:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: NEC VR Memory map MMIO locatedat 30MB (VR=0)
+
+      vr-mmio-62mb:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: NEC VR Memory map MMIO locatedat 62MB (VR=1)
+
+  gpio-pin-control:
+    type: object
+    description: GPIO control configuration.
+    properties:
+      pin:
+        type: object
+        properties:
+          gpio:
+            $ref: /schemas/types.yaml#/definitions/flag
+            description: pin in/out use GPIO.
+          function:
+            $ref: /schemas/types.yaml#/definitions/flag
+            description: pin in/out use function.
+
+  gpio-i2c:
+    type: object
+    description: GPIO I2C definition.
+    properties:
+      i2c:
+        type: object
+        properties:
+          bus:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: I2C bus number.
+
+          sda:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: I2C SDA pin port number.
+
+          scl:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: I2C SCL pin port number.
+
+          delay:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: bit transmission delay.
+
+          timeout:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: transmission timeout.
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+
+examples:
+  # MPC5200
+  - |
+    display@1,0 {
+        compatible = "smi,sm501";
+        reg = <0x00000000 0x00800000
+               0x03e00000 0x00200000>;
+        interrupts = <1 1 3>;
+        mode = "640x480-32@60";
+        edid = [00 ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00
+                00 00 01 04 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 f0 0a 80 fb 20 e0 25 10 32 60
+                02 00 00 00 00 00 00 06 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bd];
+    };
-- 
2.39.2