[Printing-user-general] error closing *main::STDOUT in foomatic 3.0.2-33.3 on FC5

Hi all,

We're in the process of upgrading all our systems from Fedora Core 3 to Fedora
Core 5.  This also involves going from foomatic 3.0.2-13.4 to 3.0.2-33.3.

This seems to have introduced an error when testing foomatic with a local
printer (an HP Deskjet 400).  Just to give a small bit of background, our
printing system uses LPRng for spooling and foomatic as the filter for certain
types of printers (typically locally attached ones).

The printcap is...

dj400|Test Queue|HP DeskJet 400|My Office:
    :ppd=/etc/foomatic/lpd/dj400.ppd:
    :lf=/var/log/lp-errs:
    :sd=/var/spool/lpd/dj400:
    :lp=/dev/lp0:
    :if=/usr/bin/foomatic-rip:
    :sh:
    :force_localhost:
    :mx=0:

and was configured with the command...

/usr/bin/foomatic-configure -q -n dj400 -N "Test Queue" -L "My Office" -d
"hpijs" -p "HP-DeskJet_400" -c "file:/dev/lp0" -s "lprng"  -o
"PrintoutMode=Draft.Gray"  -o "PageSize=A4"

This exact same setup worked OK under FC3/foomatic-3.0.2-13.4.	Now, however it
fails to print anything and gives the following output...

renderer command: gs -q -dBATCH -dPARANOIDSAFER -dQUIET -dNOPAUSE -sDEVICE=ijs
-
sIjsServer=hpijs -sDeviceManufacturer="HEWLETT-PACKARD" -sDeviceModel="DESKJET
5
40" -dDEVICEWIDTHPOINTS=595 -dDEVICEHEIGHTPOINTS=842 -r300
-sIjsParams=Quality:Q
uality=1,Quality:ColorMode=0,Quality:MediaType=0,Quality:PenSet=0
-dIjsUseOutput
FD -sOutputFile=- -
Closing renderer
foomatic-gswrapper: gs '-dBATCH' '-dPARANOIDSAFER' '-dQUIET' '-dNOPAUSE'
'-sDEVI
CE=ijs' '-sIjsServer=hpijs' '-sDeviceManufacturer=HEWLETT-PACKARD'
'-sDeviceMode
l=DESKJET 540' '-dDEVICEWIDTHPOINTS=595' '-dDEVICEHEIGHTPOINTS=842' '-r300'
'-sI
jsParams=Quality:Quality=1,Quality:ColorMode=0,Quality:MediaType=0,Quality:PenS
e
t=0' '-dIjsUseOutputFD' '-sOutputFile=/dev/fd/3' '/dev/fd/0' 3>&1 1>&2
Process dying with "error closing *main::STDOUT", exit stat: 9
        error: Broken pipe (32)
KID3 exited with status 0
KID4 exited with status 9
Renderer exit stat: 9
KID3 finished
Renderer process finished
Killing process 736 (KID3)
Process dying with "Error closing renderer", exit stat: 9
        error: Bad file descriptor (9)

If I run the above gs commands by hand (both the original and the one generated
by foomatic-gswrapper) it works fine and sends valid printable pcl to stdout.

I'd be very grateful if anybody could shed any light on this.

Cheers
Toby Blake
University of Edinburgh