Re: RemoteConfig with XFree86 Ver 3
Diego Torres Milano <[email protected]>
| Newsgroups | gmane.linux.pxes.devel |
|---|---|
| Message-ID | <1068295968.1931.4.camel@zebra> |
On Sat, 2003-11-08 at 08:21, Limesh Parekh wrote:
Dear Sir,
I was successfully able to use, Remote configuration with XFree86 Ver 4. But
if i use it with ver 3 i get error while booting the node.
The last lines of /tmp/x.err is as follows:
--------------------------------------------------------------
HorizSync 31-35
^^
Monitor section keyword expected.
--------------------------------------------------------------
Should be a bug.
Try editing the file to locate the problem. You can edit
/etc/X11/XF86Config after booting and launch X from command prompt to
locate the problem.
Also, try setting those frequencies in pxesconfig.
The whole thing works perfectly if i use, Xfree ver 4 while pxesconfig. Can
any one help me.
Is it true that Remote configuration cannot be used, with ver 3.
You can use Remote Configuration in both versions.
Limesh Parekh,
Enjay Computer Consultancy,
----------------------------------------------------------------------------
-
http://www.enjayworld.com
----------------------------------------------------------------------------
-
[email protected]
[email protected]
CHAT ID : [email protected]
[email protected]
Tel : 98241-06297
0260-3107650 (reliance)
0260-2785124 (office)
----------------------------------------------------------------------------
-
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of
[email protected]
Sent: Wednesday, August 06, 2003 8:51 AM
To: [email protected]
Subject: pxes-devel digest, Vol 1 #348 - 4 msgs
Today's Topics:
1. Re: Error : Failed to open display (Diego Torres Milano)
2. Re: pxesconfig-0.6 (Chris Gianelloni)
3. Re: Error : Failed to open display ([email protected])
4. Re: Re: pxes-devel digest, Vol 1 #342 - 2 msgs
([email protected])
--__--__--
Message: 1
Date: Tue, 5 Aug 2003 16:24:36 -0300 (ART)
Subject: Re: [pxes-devel] Error : Failed to open display
From: "Diego Torres Milano" <[email protected]>
To: <[email protected]>
Reply-To: [email protected]
I think that is a lot better to use the monitor's manual.
> Another thing you might try is to install RedHat 9.0 (or another
> version of linux) on the machine that is giving the error. Then you
> can use the etc/X11/XF86Config file to find the frequency range for
> your monitor.
>
> On Monday 04 August 2003 05:34 am, Your Friend Forever wrote:
--__--__--
Message: 2
Subject: Re: [pxes-devel] pxesconfig-0.6
From: Chris Gianelloni <[email protected]>
To: [email protected]
Date: 05 Aug 2003 15:38:41 -0400
Reply-To: [email protected]
--=-f5b3vAhXZ7cu2vBJc/w1
Content-Type: text/plain
Content-Transfer-Encoding: quoted-printable
Sounds great! I'll have to stick with 0.5.1 until then. Don't forget to
stop by the Gentoo booth and say hi to those guys.
On Tue, 2003-08-05 at 15:11, Diego Torres Milano wrote:
> Chris:
> I really want to collaborate with you to port PXES to Gentoo, but I'm
>now at the LinuxWorld Conference and cannot have access to my
--__--__--
Message: 3
To: [email protected]
Subject: Re: [pxes-devel] Error : Failed to open display
Date: Tue, 5 Aug 2003 15:13:53 -0500
From: [email protected]
Reply-To: [email protected]
Only when you can find the manual :-)
--__--__--
Message: 4
To: [email protected]
Subject: Re: [pxes-devel] Re: pxes-devel digest, Vol 1 #342 - 2 msgs
Date: Tue, 5 Aug 2003 15:50:25 -0500
From: [email protected]
Reply-To: [email protected]
Looks like this may be the beginning of a howto or more likely a faq.
Failed to open Display ":0:0" messages indicate that X can not start. This
may
be because the incorrect frequency ranges have been specified or if using
autdetect monitor, the monitor could not be identified (and thus the
incorrect frequency ranges are being used). Try manually specifiying the
correct horizontal and vertical frequency ranges in pxesconfig. Check your
monitor manual for these values. As a last resort if you can't find the
manual and searching the internet does not help, you can try booting the
thin
client using a bootable RedHat Linux installation cd (or probably other
distributions also) that uses a graphical installation. Once the graphical
installation starts (meaning that X is running), hit ctrl-alt-f2 to get a
command prompt. Type less /tmp/XF86Config.test, and look for the Monitor
section for your monitor. Write down the HorizSync and the VertRefresh
ranges
so that you can use them when you run pxesconfig. Instead of booting from an
install CD, you could also try booting from a hard drive that has Linux and
X
installed, and then locating the values in the /etc/X11/XF86Config file
under
the Monitor section.
Another thing to try is to reduce the color depth and/or resolution since
your
video card may not have enough memory to support 24 bit color at your
selected resolution.
As long as you are able to run X on the hardware one way or another, you
should be able to run X with pxes linux, it is just a matter of getting the
XF86Config file set up correctly for the hardware.
Please correct any errors and add to this answer as needed to make it
suitable
to add to the pxes faq.
On Saturday 02 August 2003 06:30 am, Your Friend Forever wrote:
> Dear Sir ,
> I already tried to select the RDP server name or IP address
> while in configuration screen but in vain. that is the problem
> persist. I want to know the some things about pxesconfig-0.6 that is
> it compatible with diskless clients having Intel810 display or AGP
> from trident? why I am getting such messages like Failed to open
--
______ ________
/ / \/ /___ ) I N T E G R A C I O N
/ / /___ / I N F O R M A T I C A
/__/__/\___/_____'
Diego Torres Milano Maipu 42 Office 164 (1084) BA Argentina
[email protected] Tel: +5411 4331-2233 www.in3.com.ar
-------------------------------------------------------
This SF.Net email sponsored by: ApacheCon 2003,
16-19 November in Las Vegas. Learn firsthand the latest
developments in Apache, PHP, Perl, XML, Java, MySQL,
WebDAV, and more! http://www.apachecon.com/