Re[8]: ROM image for Realtek 8029AS
"Vladimir P. Doykin" <[email protected]>
| Newsgroups | gmane.linux.pxes.devel |
|---|---|
| Organization | mcd |
| Message-ID | <[email protected]> |
Hello Ben, Thursday, November 20, 2003, 4:55:51 AM, you wrote: > Our EPROM eraser has now been fixed so I have been able to erase some 32K > 28C128 EPROMs. I think it is 16K EEPROM or am I wrong? > I have programmed them with the 16K rom-o-matic image > (offset=0 which is the default) and verified them. The jumperless network > card is set for boot ROM enabled, rom size =32K then 16K should be. > but it still won't boot! > (Operating system not found) > Any ideas? I haven't had any success with jumperless NICS and PCI nics. The > only success I had was with an ISA jumpered NE2000 nic. > Or do these cards expect a different offset? > Ben. > -----Original Message----- > From: [email protected] > [mailto:[email protected]]On Behalf Of Vladimir P. > Doykin > Sent: Tuesday, 4 November 2003 8:56 PM > To: [email protected] > Subject: Re[6]: [pxes-devel] ROM image for Realtek 8029AS > Tuesday, November 04, 2003, 1:16:40 PM, you wrote: >> We tried eb-5[1].2.2-rtl8029.zrom > Well, I ran setup utility for my NIC and turned off PnP mode. Then > I set IRQ and I/O PORT and burnt ne-5.0.8-ne.lzrom image into EEPROM. >> What's wrong with the 27C***? That's what we are trying to use. They work >> fine in NE2000 jumpered ISA cards. > I think they are right for nonreusable burning. Sometimes ultraviolet don't > erase > data fully from chip, less convenient and less reliable, but more > cheaper (1.3 USD). 28C*** is more convenient, reliable, but more > expansive (6 USD). >> Thanks, >> Ben. >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]]On Behalf Of Vladimir P. >> Doykin >> Sent: Tuesday, 4 November 2003 6:57 PM >> To: [email protected] >> Subject: Re[4]: [pxes-devel] ROM image for Realtek 8029AS >> I have working NIC on 8029 chip on PCI bus. There are no problems with >> image taken from rom-o-matic. I used ver 5.0.8., EEPROM AT28C256 >> (because of 27C*** is sucks). Computer was P166 MMX. All is working >> perfect. >> Which image did you take from rom-o-matic? Give full name of file >> please. >> Tuesday, November 04, 2003, 3:10:37 AM, you wrote: >>> We are having a similar problem - works with floppy image but doesn't > boot >>> from a boot ROM- if you look at the specifications for the realtek > chipset >>> it only supports 8, 16 and 32 Kbit EPROMS. We are waiting for our eraser >> to >>> be fixed so I can erase and reprogram a 32K EPROM. I'll let you know if > we >>> are successful. >>> Please tell me if you have any success. >>> Ben. >>> -----Original Message----- >>> From: [email protected] >>> [mailto:[email protected]]On Behalf Of #1 >>> Sent: Tuesday, 4 November 2003 3:58 AM >>> To: Ben Reuter >>> Subject: Re[2]: [pxes-devel] ROM image for Realtek 8029AS >>> Hi, Ben! >>> Monday, November 3, 2003, 12:12:40 AM, you wrote: BR>>>> The etherboot one works fine for us. We got ours from >>> www.rom-o-matic.com BR>>>> which is a bit easier to use. >>> Many thanks for your interest with my problem. >>> I tryed the programm Etherboot images (from rom-o-matic and my PC ;-)) > for >>> realtek 8029AS PCI >>> card. >>> I used different chips with ultraviolet- and electroerase - different >>> 27c256's and winbond w27c512. I've tried 16 kb image, and the glue >>> together (twice for 256 kbit chip and to fold in four for w27c512). >>> But there was only one result - PC freeze after POST (with string: >>> "Press F2 for BIOS, Press F12 for boot from network"). >>> I've attempted with different bioses (new Pentium 4 and oldest >>> P1-200Mhz) - but wrongly! >>> At the same time - boot image for diskette works fine! >>> And the same programmed chips for Realtek 8139D (with proper image >>> insertion) >>> work fine too! >>> Can you help me - what else can I try-on? >>> Respect for you. >>> ------------------------------------------------------- >>> This SF.net email is sponsored by: SF.net Giveback Program. >>> Does SourceForge.net help you be more productive? Does it >>> help you create better code? SHARE THE LOVE, and help us help >>> YOU! Click Here: http://sourceforge.net/donate/ >>> _______________________________________________ >>> pxes-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/pxes-devel >>> ------------------------------------------------------- >>> This SF.net email is sponsored by: SF.net Giveback Program. >>> Does SourceForge.net help you be more productive? Does it >>> help you create better code? SHARE THE LOVE, and help us help >>> YOU! Click Here: http://sourceforge.net/donate/ >>> _______________________________________________ >>> pxes-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/pxes-devel >> -- >> Best regards, >> Vladimir mailto:[email protected] >> ------------------------------------------------------- >> This SF.net email is sponsored by: SF.net Giveback Program. >> Does SourceForge.net help you be more productive? Does it >> help you create better code? SHARE THE LOVE, and help us help >> YOU! Click Here: http://sourceforge.net/donate/ >> _______________________________________________ >> pxes-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/pxes-devel >> ------------------------------------------------------- >> This SF.net email is sponsored by: SF.net Giveback Program. >> Does SourceForge.net help you be more productive? Does it >> help you create better code? SHARE THE LOVE, and help us help >> YOU! Click Here: http://sourceforge.net/donate/ >> _______________________________________________ >> pxes-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/pxes-devel > -- > Best regards, > Vladimir mailto:[email protected] > ------------------------------------------------------- > This SF.net email is sponsored by: SF.net Giveback Program. > Does SourceForge.net help you be more productive? Does it > help you create better code? SHARE THE LOVE, and help us help > YOU! Click Here: http://sourceforge.net/donate/ > _______________________________________________ > pxes-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/pxes-devel > ------------------------------------------------------- > This SF.net email is sponsored by: SF.net Giveback Program. > Does SourceForge.net help you be more productive? Does it > help you create better code? SHARE THE LOVE, and help us help > YOU! Click Here: http://sourceforge.net/donate/ > _______________________________________________ > pxes-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/pxes-devel -- Best regards, Vladimir mailto:[email protected] ------------------------------------------------------- This SF.net email is sponsored by: SF.net Giveback Program. Does SourceForge.net help you be more productive? Does it help you create better code? SHARE THE LOVE, and help us help YOU! Click Here: http://sourceforge.net/donate/